Isuzu engine C22NE / 22LE / 20LE. Manual — part 108
DRIVEABILITY AND EMISSIONS 6E1-261
FUEL METERING SYSTEM
ACCELERATOR CABLE ASSEMBLY
Removal
1.
Loosen the adjusting nut on the cable bracket mounting
on the throttle body.
2.
Remove the cable clip from holding bracket.
3.
Remove accelerator control cable (on the throttle valve
end).
4.
Remove the accelerator control cable (on the accelerator
pedal end).
5.
Remove the grommet.
6.
Remove the accelerator control cable.
Inspection
Check the following items, and replace the control cable if any
abnormality is found:
•
The control cable should move smoothly.
•
The control cable should not be bent or kinked.
•
The control cable should be free of damage and
corrosion.
Installation
1. Install the accelerator control cable.
2. Install the grommet.
3.
Install the accelerator control cable on the accelerator
pedal.
4.
Install the accelerator control cable on the throttle valve.
5. Install the cable clip to the holding bracket.
6. Adjust the accelerator cable. Refer to Accelerator Cable
Adjustment Section.
6E1-262 DRIVEABILITY AND EMISSIONS
ACCELERATOR CABLE
ADJUSTMENT
Adjustment
1. Loosen the adjusting nut.
2. Loosen the jam nut.
3. Pull the outer cable while fully closing the throttle valve.
4. Tighten the adjusting nut.
5. Tighten the jam nut.
6. Loosen the adjusting nut and adjust clearance between
adjusting nut and bracket to 2
∼3.5mm.
7. Tighten the jam nut again.
8. Manually operate valve.
Important: The valve lever must return up to the stopper screw.
If the valve lever does not reach the stopper screw, repeat the
procedure again from Step 1.
ACCELERATOR PEDAL
REPLACEMENT
Removal
1. Disconnect the accelerator pedal control cable from the
accelerator pedal assembly.
2. Remove the two screws retaining the accelerator pedal to
the bulkhead.
3. Remove the accelerator pedal from the bulkhead.
Installation
1. Install the accelerator pedal assembly to the bulkhead
with two screws.
2. Connect the accelerator control cable to the accelerator
pedal assembly.
3. Adjust accelerator cable if necessary. Refer to
Accelerator Control Cable Adjustment Section.
DRIVEABILITY AND EMISSIONS 6E1-263
FUEL FILLER CAP
The Fuel Filler Cap includes a vacuum valve. If high vacuum
occurs in the fuel tank, the vacuum valve works to adjust the
pressure in order to prevent damage to the tank.
Inspection
Notice: Replace the fuel filler cap with the same type of filler
cap that was originally installed on the vehicle.
•
Check the seal ring in the filler cap for any abnormality
and for seal condition.
•
Replace the filler cap if any abnormality is found.
WARNING
REMOVE SLOWLY
FUEL SPRAY MAY
CAUSE INJURY
FUEL FILTER
Removal
1. Disconnect the negative battery cable.
2. Remove the fuel filler cap.
3. Disconnect the fuel line from the fuel filter on the engine
side.
4. Disconnect the fuel line from the fuel filter on the fuel
tank side.
5. Remove the bolt on the fuel filter holder.
6. Remove the fuel filter.
Inspection
1. Replace the fuel filter when the following occur:
• Fuel leaks from the fuel filter body
• The fuel filter body is damaged
• The fuel filter is clogged with dirt or sediment
2. If the drain hole is clogged with dust, clean the drain hole
with air.
6E1-264 DRIVEABILITY AND EMISSIONS
Installation
1. Install the fuel filter in the correct direction.
2. Install the bolt on the fuel filter holder.
3. Connect the fuel line on the engine side.
4. Connect the fuel line on the fuel tank side.
5. Install the fuel filler cap.
6. Connect the negative battery cable.
FUEL INJECTORS
Removal
Notice: If the fuel injectors are leaking, the engine oil may be
contaminated with fuel. Check the oil for signs of contamination
and change the oil and filter if necessary.
Notice: Use care in removing the fuel injector in order to
prevent damage to the fuel injector al connector pins or fuel
injector nozzles. The fuel injector is an al component and
should not be immersed in any type of cleaner as this may
damage the fuel injector.
Important: Fuel injectors are serviced as complete assembly
only.
1. Disconnect the negative battery cable.
2. Disconnect al connector from fuel injector.
3. Remove the fuel rail. Refer to Fuel Rail Removal
Procedure.
4. Remove the fuel injector retainer clip.
5. Remove the fuel injector assembly from fuel rail.
6. Remove O-ring from the fuel injector.
7. Remove O-ring backup from fuel injector.
Inspection
1. Inspect O-ring for crack, damage or leaks.
2. Replace worn or damaged O-ring.
3. Lubricate the new O-rings with engine oil before
installation.
Installation
1. Lubricate the new O-ring with engine oil.
2. Install the O-ring backup on the fuel injector.
3. Install new O-ring on the fuel injector.
4. Install all four injector on the fuel rail.
5. Use new injector retainer clip to retain the injetor to the
fuel rail.
6. Coat the end of the fuel injector with engine oil.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст