Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Manual — part 1246

ELECTRICAL-BODY AND CHASSIS 8-323

2. Mirror on the left (or right) side does not operate

Checkpoint

Trouble

Cause

Countermeasure

Replace the door mirror
control SW.

SW. malfunction

NG

Repair or replace the door
mirror

Mirror function on the left (or
right) side

Mirror malfunction on the left
(or right)

Repair open circuit or
connector contact

Continuity between
[LHD]
1

B-26

and 2

D-2

(1

B-26

and 2

D-7

)

[RHD]
1

B-26

and 2

D-7

(1

B-26

and 2

D-2

)

Open circuit or poor connector
contact

NG

NG

OK

OK

Door mirror control SW.
function

3. Mirrors on the both sides operate only in the vertical (or horizontal) direction

Replace the door mirror
control SW.

SW. malfunction

NG

Door mirror control SW.
function

8-324 ELECTRICAL-BODY AND CHASSIS

4. Mirror on the left side operates only in the vertical (or horizontal) direction

Checkpoint

Trouble

Cause

Countermeasure

Replace the door mirror
control SW.

SW. malfunction

NG

Repair or replace the door
mirror

Door mirror function

Door mirror malfunction

Repair open circuit or
connector contact

Continuity between
[LHD]
8

B-26

and 3

D-2

(10

B-26

and 1

D-7

)

[RHD]
8

B-26

and 3

D-7

(10

B-26

and 1

D-2

)

Open circuit or poor connector
contact

NG

NG

OK

OK

Door mirror control SW.
function

5. Mirror on the right side operates only in the vertical (or horizontal) direction

Replace the door mirror
control SW.

Door mirror control
malfunction

NG

Repair or replace the door
mirror

Door mirror function

Door mirror malfunction

Repair open circuit or
connector contact

Continuity between
[LHD]
7

B-26

and 3

D-7

(5

B-26

and 1

D-7

)

[RHD]
7

B-26

and 3

D-2

(5

B-26

and 1

D-2

)

Open circuit or poor connector
contact

NG

NG

OK

OK

Door mirror control SW.
function

ELECTRICAL-BODY AND CHASSIS 8-325

REMOVAL AND INSTALLATION

DOOR MIRROR CONTROL SWITCH

Removal

1. Instrument Panel Cluster Assembly

· Refer to section 10 “BODY” for instrument panel cluster

assembly removal steps.

2. Door Mirror Control Switch

· Disconnect the switch connector.
· To remove the switch, push the lock from the back side

of the cluster assembly.

Installation

To install, follow the removal steps in the reverse order.

DOOR MIRROR

Removal and Installation

Refer to the DOOR MIRROR in section 10 “BODY”.

8-326 ELECTRICAL-BODY AND CHASSIS

INSPECTION AND REPAIR

Switch side

Door Mirror Control Switch

1. Switch side Connector Circuit
Check continuity between the switch connector terminals

while operating the door mirror control switch as shown in
the following table.

Connector No.

Switch position

4 9 1 8 10 7 5

(Up)

(Down)

(Left)

(Right)

(Up)

(Down)

(Left)

(Right)

Harness side

2. Harness Side Connector Circuit
Remove the connector No.

B-26

of the mirror control

switch and check voltage and continuity of the harness side
connector.
· When there is no continuity at the terminal No. 5, 7, 8

and 10, it is considered that the circuit with terminal No.
1 (B/W) is defective.

Door mirror (RH)

Door mirror (LH)