Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Manual — part 965
4C1-30 FRONT WHEEL DRIVE
5. Cross Pin
(1) Be sure to install the cross pin so that it is in alignment with
the lock pin hole in the differential cage.
(2) Adjust the backlash between the side gear and the pinion
gear.
mm(in)
Backlash
0.03 - 0.08 (0.001 - 0.003)
Thickness of thrust washers available
mm(in)
167 mm
1.05, 1.15, 1.25 (0.041, 0.043, 0.049)
194 mm
1.00, 1.05, 1.10 (0.039, 0.041, 0.043)
6. Lock Pin
After lock pin installation, stake the cage to prevent discharge
of the lock pin.
7. Ring Gear
When installing the ring gear, apply LOCTITE 271 or equivalent
to the threaded hole and bolt.
8. Bolt
Tighten the bolts in diagonal sequence as illustrated.
Bolt Torque
N
⋅
m (kgf
⋅
m/lb
⋅
ft)
167 mm
78.5
±
9.8 (8
±
1/57.9
±
7.2)
194 mm
107.9
±
9.8 (11
±
1/79.6
±
7.2)
Note :
Discard used bolts and install new ones.
For 167 mm
Note that all bolts have a left hand thread.
FRONT WHEEL DRIVE 4C1-31
MAJOR COMPONENTS
Reassembly Steps
1. Diff. carrier
▲
2. Outer bearing outer race
▲
3. Inner bearing outer race
▲
4. Adjust shim
▲
5. Inner bearing
▲
6. Collapsible spacer
7. Pinion gear
8. Outer bearing
▲
9. Oil seal
10. Dust cover
11. Flange
▲
12. Flange nut and washer
▲
13. Adjust shim
▲
14. Side bearing
15. Bearing outer race
16. Diff. cage assembly
▲
17. Bearing cap
▲
18. Bolt
19. Axle case
▲
20. Differential assembly
21. Bolt
4C1-32 FRONT WHEEL DRIVE
Important Operations
2. Outer Bearing Outer Race
Installer : 5-8522-0048-0 (167 mm)
(J-29038)
9-8522-1141-0 (194 mm)
(J-24256)
Grip
: 5-8840-0007-0
(J-8092)
3. Inner Bearing Outer Race
Installer : 5-8522-0049-0 (167 mm)
(J-29039)
9-8522-1274-0 (194 mm)
Grip
: 5-8840-0007-0
(J-8092)
4. Adjust Shim
Adjustment of drive pinion mounting distance
(1) Apply gear oil to the inner and outer drive pinion bearing.
Clean the pinion setting gage set.
Then install the gage set together with the inner and outer
bearings.
For 167 mm
1
Pilot
: 5-8840-2092-0
(J-23597-28)
2
Nut and bolt : 5-8840-0127-0
(J-21777-43)
3
Rear pilot
: 5-8840-02091-0
(J-23597-27)
4
Gage plate : 5-8840-2090-0
(J-23597-26)
For 194 mm
1
Pilot
: 5-8840-2085-0
(J-21777-42)
2
Nut and bolt : 5-8840-2089-0
(J-23597-9)
4
Gage plate : 5-8840-2087-0
(J-23597-7)
FRONT WHEEL DRIVE 4C1-33
Tighten the nut to the specified torque.
N
⋅
m (kgf
⋅
m/lb
⋅
ft)
New bearing
2.26 (23/20)
Used bearing
0.98 - 1.18
(10 - 12/8.7 - 10.4)
(2) Clean the side bearing bores. Install the dial indicator with
the discs and Arbor. Install and tighten the bearing caps to
the specified torque.
Torque
N
⋅
m (kgf
⋅
m/lb
⋅
ft)
167 mm
68.7
±
9.8 (7.0
±
1.0/50.6
±
7.2)
194 mm
98.1
±
9.8 (10.0
±
1.0/72.3
±
7.2)
For 167 mm
1
Dial indicator : 5-8840-0126-0
(J-8001)
2
Disc (2 pcs.) : 5-8840-2086-0
(J-23597-4)
3
Arbor
: 5-8840-0128-0
(J-23597-1)
4
Gage plate
: 5-8840-2090-0
(J-23597-26)
For 194 mm
1
Dial indicator : 5-8840-0126-0
(J-8001)
2
Disc (2 pcs.) : 5-8840-2088-0
(J-23597-8)
3
Arbor
: 5-8840-0128-0
(J-23597-1)
4
Gage plate
: 5-8840-2087-0
(J-23597-7)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст