Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Manual — part 1556

8-324 ELECTRICAL-BODY AND CHASSIS

4.Mirror on the left side operates only in the vertical (or horizontal) direction

Checkpoint

Trouble Cause

Countermeasure

Replace the door mirror

control SW.

SW. malfunction

NG

Repair or replace the door

mirror

Door mirror function

Door mirror malfunction

Repair open circuit or
connector contact

Continuity between
[LHD]
8

B-26

and 3

D-2

(10

B-26

and 1

D-7

)

[RHD]
8

B-26

and 3

D-7

(10

B-26

and 1

D-2

)

Open circuit or poor connector

contact

NG

NG

OK

OK

Door mirror control SW.

function

5.Mirror on the right side operates only in the vertical (or horizontal) direction

Replace the door mirror

control SW.

Door mirror control

malfunction

NG

Repair or replace the door

mirror

Door mirror function

Door mirror malfunction

Repair open circuit or
connector contact

Continuity between
[LHD]
7

B-26

and 3

D-7

(5

B-26

and 1

D-7

)

[RHD]
7

B-26

and 3

D-2

(5

B-26

and 1

D-2

)

Open circuit or poor connector

contact

NG

NG

OK

OK

Door mirror control SW.

function

ELECTRICAL-BODY AND CHASSIS 8-325

REMOVAL AND INSTALLATION

DOOR MIRROR CONTROL SWITCH

Removal

1.Instrument Panel Cluster Assembly

• Refer to section 10 “BODY” for instrument panel cluster

assembly removal steps.

2.Door Mirror Control Switch

• Disconnect the switch connector.
• To remove the switch, push the lock from the back side

of the cluster assembly.

Installation

To install, follow the removal steps in the reverse order.

DOOR MIRROR

Removal and Installation

Refer to the DOOR MIRROR in section 10 “BODY”.

8-326 ELECTRICAL-BODY AND CHASSIS

INSPECTION AND REPAIR

Switch side

Door Mirror Control Switch

1.Switch side Connector Circuit

Check continuity between the switch connector terminals

while operating the door mirror control switch as shown in

the following table.

Connector No.

Switch position

4

9

1

8

10

7

5

(Up)

(Down)

(Left)

(Right)

(Up)

(Down)

(Left)

(Right)

Harness side

2.Harness Side Connector Circuit

Remove the connector No.

B-26

of the mirror control

switch and check voltage and continuity of the harness side

connector.
• When there is no continuity at the terminal No. 5, 7, 8

and 10, it is considered that the circuit with terminal No.

1 (B/W) is defective.

Door mirror (RH)

Door mirror (LH)

ELECTRICAL-BODY AND CHASSIS 8-327

• When there is no continuity at either one of the circuit

No, 5, 7, 8, or 10, the motor in the mirror of the circuit or

the circuit itself is defective.

Terminal

No.

Wire

color

Connection to

Check item

Connecting

terminal

Check condition

Standard

1

B/W

LH mirror & RH

mirror

Continuity

1-Ground

-

No continuity

4

R/L

Fuse CB-19 (15A)

Voltage

4-Ground

Starter SW “ACC”

position

Approx.

12V

5

V

RH mirror-LH/RH

5-1

-

7

W/B

RH mirror-Up/Down

7-1

-

8

W/G

LH mirror-Up/Down

Continuity

8-1

-

Continuity

9

B

Ground

9-Ground

-

10

B/R

LH mirror-LH/RH

10-1

-

Harness side

Door Mirror

1.Door Mirror Control Switch Connector Circuit

Disconnect the switch connector (

B-26

), apply the battery

voltage to the harness side connector terminals and check

its function.

Connector

No.

B-26

Operating

Terminal

Mirror

No.

10

5

1

8

7

direction

+

-

Left

-

+

Right

-

+

Up

+

-

Down

+

-

Left

-

+

Right

-

+

Up

+

-

Down

Left

Right