Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Manual — part 1313
8–172 ELECTRICAL-BODY AND CHASSIS
DOOR SWITCH
Removal
1. Push the door switch sliding portion 1 in the
direction of the arrow in the illustration.
2. Loosen the screw 2.
3. Pull the switch free to remove it.
4. Disconnect the door switch connector.
1
2
D08RV874
2. Disconnect the connector 2.
3. Push the bulb in and turn it counterclockwise to
remove it.
2
D08RV876
Installation
Follow the removal procedure in the reverse order to
install the spot light.
Pay close attention to the important points mentioned in
the following paragraphs.
SPOT LIGHT
Removal
1. Grasp the spot light housing 1 with both hands.
Pull the housing straight down.
This will release the clip.
1
D08RV875
Connector
Be absolutely sure that the door switch connector is
securely connected.
This will prevent a poor contact and an open circuit.
ELECTRICAL-BODY AND CHASSIS 8–173
Installation
Follow the removal procedure in the reverse order to
install the spot light.
Pay close attention to the important points mentioned in
the following paragraphs.
Connector
Be absolutely sure that the spot light connector is
securely connected.
This will prevent a poor contact and an open circuit.
Bulb
Be absolutely sure that the spot light bulb is correctly
installed.
This will prevent a poor contact and an open circuit.
Installation
Follow the removal procedure in the reverse order to
install the warning buzzer.
Pay close attention to the important points mentioned in
the following paragraphs.
Connector
Be absolutely sure that the warning buzzer connector is
securely connected.
This will prevent a poor contact and an open circuit.
WARNING BUZZER
Removal
1. Dash Side Panel
2. Warning Buzzer
•
Disconnect the connector.
•
Remove the screw.
2. Warning buzzer
1. Dash side panel
This illustration is based on LHD
825RV105
8–174 ELECTRICAL-BODY AND CHASSIS
DOOR SWITCH
Door Switch Connections
SEAT BELT SWITCH (SAUDI ARABIA, SOUTH
AFRICA)
Seat Belt Switch Connections
825RV106
Connector
No.
SW
Terminal No.
position
1
Body Ground
PUSHED
RELEASED
INSPECTION AND REPAIR
L-3
L-8
R-1
R-6
L-3
L-8
R-1
R-6
1
2
R-3
Switch side
Connector No.
SW
position
Terminal No.
1
2
ON (Belt tongue removed)
OFF (Belt tongue inserted)
R-3
ELECTRICAL-BODY AND CHASSIS 8–175
WARNING BUZZER (SAUDI ARABIA)
1. Warning Buzzer Circuit
Warning function
Operational conditions
The warning light in the meter assembly turned on about 6 seconds
from the moment the starter switch is turned on.
The buzzer sounds for about 6 seconds when the starter switch is
turned on with the seat belt switch on (when the seat belt is not
used).
The buzzer sounds when both the key remind switch and the FRT
door switch-LH are turned on.
To stop the sound of the buzzer, turn on the starter switch.
The buzzer sounds when the starter switch is turned from the “on”
to “off” position while the taillights are on.
Door SW
(Driver
side)
Warning buzzer
Seat belt
SW
Seat belt
warning
light
Starter
SW
Key
remind
SW
Tail
relay
+
–
3
4
6
5
1
2
D08RV991
2. Warning Buzzer Harness Side Connector Circuit
Disconnect the warning buzzer connector and check
continuity and voltage between the warning buzzer
harness side connector terminals.
1
2
3
6
4 5
B-5
Harness side
Fasten the seat belt
Key left in starter switch
Taillights left on
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст