Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Manual — part 1386
ELECTRICAL-BODY AND CHASSIS 8-109
Installation
Follow the removal procedure in the reverse order to install the
spot light.
Pay close attention to the important points mentioned in the
following paragraphs.
Connector
Be absolutely sure that the spot light connector is securely
connected.
This will prevent a poor contact and an open circuit.
Bulb
Be absolutely sure that the spot light bulb is correctly installed.
This will prevent a poor contact and an open circuit.
WARNING BUZZER (For Gulf only)
Removal
1. Dash Side Panel
2. Warning Buzzer
• Disconnect the connector.
• Remove the screw.
Installation
Follow the removal procedure in the reverse order to install the
warning buzzer.
Pay close attention to the important points mentioned in the
following paragraphs.
Connector
Be absolutely sure that the warning buzzer connector is
securely connected.
This will prevent a poor contact and an open circuit.
8-110 ELECTRICAL-BODY AND CHASSIS
INSPECTION AND REPAIR
DOOR SWITCH
Door Switch Connections
Connector
SW
No.
L-3
L-8
R-1
R-6
position
Terminal No.
1Body Ground
PUSHED
RELEASED
Switch side
SEAT BELT SWITCH (GULF, SOUTH
AFRICA)
Seat Belt Switch Connections
Connector
SW
No.
R-3
position
Terminal No.
1
2
ON (Belt tongue removed)
OFF (Belt tongue inserted)
ELECTRICAL-BODY AND CHASSIS 8-111
WARNING BUZZER (For Gulf only)
1. Warning Buzzer Circuit
Warning function
Operational conditions
The warning light meter assembly turned about 6 seconds from the
moment the starter switch is turned on.
The buzzer sounds for about 6 seconds when the starter switch is turned
on with the seat belt switch on (when the seat belt is not used).
Key left in starter switch
The buzzer sounds when both the key remind switch and the FRT door
switch-LH are turned on.
To stop the sound of the buzzer, turn on the starter switch.
Tail lights left on
The buzzer sounds when the starter switch is turned from the “on” to “off”
position while the taillights are on.
Harness side
2. Warning Buzzer Harness Side Connector Circuit
Disconnect the warning buzzer connector and check
continuity and voltage between the warning buzzer harness
side connector terminals.
Fasten the seat belt
8-112 ELECTRICAL-BODY AND CHASSIS
Terminal
NO.
Wire
color
Connecting to
Check item
Connecting
terminal
Check condition
Standard
Seat
Unfasten
Continuity
belt
Fasten
No continuity
3
G/Y
Tail relay
3-Ground
Light SW “ON”
Approx. 12V
Key remind SW
Insert
Approx. 12V
(Starter SW)
Remove
0V
6
Y
Fuse CB-7
6-Ground
Starter SW “ON”
Approx. 12V
Door SW
Open
Continuity
(FRT-LH)
Continuity
Close
No continuity
2
B
Ground
2-Ground
-
Continuity
WARNING BUZZER (For Gulf only)
1. Warning Buzzer Circuit
Warning function
Operational conditions
Fasten the seat belt
The buzzer sounds when the starter switch is turned on with the seat belt
switch on (when the seat belt is not used)
Key left in starter switch
The buzzer sounds when both the key remind switch and the FRT door
switch-LH are turned on.
To stop the sound of the buzzer, turn on the starter switch.
Taillights left on
The buzzer sounds when the starter switch is turned from the “on” to “off “
position while the taillights are on.
5-Ground
Continuity
Seat belt SW
G/Y
5
Key
4-Ground
Voltage
R/B
4
FRT door-LH
1-Ground
B/W
1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст