Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Manual — part 1824
MSG MODEL (4WD) 7B-73
Important Operations
4. 4
××××2/4××××4 Shift Rod
6. High/Low Shift Rods
1) Remove the spring pin from the shift arm.
Spring Pin Remover : 9-8529-2201-0
2) Drive the shift rod toward the output flange.
9. Idler Gear Shaft
Attach a bolt to the idler shaft threads and remove the shaft
from the side case.
Bolt Size
Threads Pitch
8 mm
1.25
Take care not to damage and miss the thrust washers,
bearing, and idler gear.
15.Output Shaft
1) Attach the wrench to the output flange of the shaft.
2) Loosen the output shaft nut.
3) Remove the washers and the shaft.
Wrench : 5-8840-0133-0 (J-8614-01)
17.Output Shaft Front Bearing
18.Output Shaft Rear Bearing
Use the bearing remover to remove the front and the rear
bearing.
Bearing Remover : 5-8523-0010-0 (J-29040)
Grip
: 5-8840-0007-0 (J-8092)
7B-74 MSG MODEL (4WD)
INSPECTION AND REPAIR
Make the necessary adjustments, repairs, and part replacements if excessive wear or damage is discovered during
inspection.
Visual Check
Inspect the following parts for wear, damage or other abnormal
conditions.
Transfer Side Case
1. Front output shaft front bearing
2. Front output shaft rear bearing
3. Idler gear bearing
Transmission and Transfer Case
1. Rear output shaft front bearing
2. Rear output shaft pilot bearing
3. Rear output shaft pilot bearing
4. Rear output gear bearing
5. Transfer input gear bearing
6. Transfer counter gear bearing
Transmission
1. Clutch gear shaft
2. 3rd gear
3. 2nf gear
4. 1st gear
5. Reverse gear
6. Counter gear
7. Counter reverse gear
8. Reverse idle
9. 5th gear
10.5th counter gear
MSG MODEL (4WD) 7B-75
SHIFT ARM THICKNESS
Use a micrometer to measure the shift arm thickness.
If the measured value is less than the specified limit, the shift
arm must be replaced.
Shift Arm Thickness
mm(in)
Standard
Limit
1st-2nd
9.65-9.85 (0.380-0.388)
9.0 (0.354)
3rd-4th
6.95-7.2 (0.273-0.283)
6.5 (0.256)
Rev.-5th
6.8-6.9 (0.268-0.272)
6.3 (0.248)
Transfer
6.7-6.8 (0.264-0.268)
6.0 (0.236)
DETENT SPRING FREE LENGTH
Use a vernier caliper to measure the detent spring free length.
If the measured value is less than the specified limit, the detent
spring must be replaced.
Detent spring Free Length
mm(in)
Standard
limit
Transmission
25.6 (1.01)
23.6 (0.93)
Transfer
43.0 (1.69)
41.0 (1.61)
DETENT SPRING TENSION
Use a spring tester to measure the valve spring tension.
If the measured value is less than the specified limit, the valve
spring must be replaced.
Valve Spring Tension
N (kg/lb)
Compressed
Height mm(in)
Standard
Transmission
22.1 (0.870)
61.7-65.7
(6.3-6.7/13.7-14.8)
Transfer
36.1 (1.421)
19.84-24.25
(9-11)
7B-76 MSG MODEL (4WD)
BLOCK RING AND DOG TEETH
CLEARANCE
Use a thickness gauge to measure the clearance between the
block ring and the dog teeth.
If the measured value exceeds the specified limit, the block
ring must be replaced.
Block Ring and Dog Teeth Clearance
mm(in)
Standard
Limit
1st, 2nd
2.0 (0.078)
1.3 (0.051)
3rd, 4th, 5th
1.5 (0.059)
0.8 (0.031)
BLOCK RING AND INSERT CLEARANCE
Use a thickness gauge to measure the clearance between the
block ring and the inset.
If the measured value exceeds the specified limit, the block
ring and/or the insert must be replaced.
Block Ring and Insert Clearance
mm(in)
Standard
Limit
1st, 2nd
3.46-3.74 (0.136-0.147)
3rd, 4th, 5th
3.51-3.79 (0.138-0.149)
4.0 (0.157)
CLUTCH HUB AND INSERT CLEARANCE
Use a thickness gauge to measure the clearance between the
clutch hub and the insert
If the measured value exceeds the specified limit, the clutch
hub and/or the insert must be replaced.
Clutch Hub and Insert Clearance
mm(in)
Standard
Limit
0.01-0.19 (0.0004-0.0075)
0.3 (0.012)
MAINSHAFT RUN-OUT
Use a dial indicator to measure the mainshaft central portion
run-out.
If the measured mainshaft run-out exceeds the specified limit,
the mainshaft must be replaced.
Mainshaft Run-Out
mm(in)
Limit
Less than 0.03 (0.0012)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст