Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Manual — part 998
BRAKES 5-63
INSPECTION AND REPAIR
Make necessary adjustments, repairs, and parts replacements if wear, damage or other problems are discovered
during inspection.
Refer to "SERVICING" in this section for
adjustment procedure of parking brake.
Adjustment Procedure of Parking Brake
•
Parking brake
5-64 BRAKES
PARKING BRAKE (FLOOR MOUNT TYPE)
REMOVAL AND INSTALLATION
PARKING BRAKE LEVER AND FRONT CABLE ASSEMBLY
Removal Steps
1. Lock nut
2. Adjust nut
3. Equalizer
4. Center console
5. Bolt
6. Switch connector
7. Parking brake lever
8. Parking brake front cable
Installation Steps
▲
8. Parking brake front cable
7. Parking brake lever
6. Switch connector
▲
5. Bolt
4. Center console
3. Equalizer
2. Adjust nut
1. Lock nut
Important Operation - Installation
8. Parking Brake Front Cable
Apply grease (BESCO L-2 or equivalent) to the front cable
before installation.
•
After installation, be sure to adjust the parking brake.
Refer to "SERVICING" of this section.
BRAKES 5-65
REAR CABLE ASSEMBLY
Removal Steps
▲
1. Lock nut
▲
2. Adjusting nut
▲
3. Bolt
▲
4. Retainer
5. Clip and bolt ; crossmember
6. Clip and bolt ; side member
7. Clip and bolt ; side member
8. Clip and bolt ; spring eye
9. Clip and bolt ; leaf spring
10. Hand brake rear cable
Installation Steps
▲
10. Hand brake rear cable
▲
9. Clip and bolt ; leaf spring
▲
8. Clip and bolt ; spring eye
▲
7. Clip and bolt ; side member
▲
6. Clip and bolt ; side member
▲
5. Clip and bolt ; crossmember
▲
4. Retainer
▲
3. Bolt
▲
2. Adjusting nut
▲
1. Lock nut
5-66 BRAKES
Important Operations - Removal
Preparation
•
Raise vehicle to the working level.
Support the axle assembly with the proper jack and chassis
stands.
•
Remove the tire and wheel.
•
Remove the brake drum.
1. Lock Nut
2. Adjusting Nut
3. Bolt
4. Retainer
•
Loosen lock nut and adjusting nut, then disconnect rear
cable from the equalizer.
•
Remove bolt and retainer.
Important Operations - Installation
10.Hand Brake Rear Cable
•
Apply grease (BESCO L-2 or equivalent) to the
circumference of the pin and joint.
•
Apply grease (BESCO L-2 or equivalent) to the equalizer
joint portion.
9. Clip and Bolt; Leaf Spring
8. Clip and Bolt; Spring Eye
7. Clip and Bolt; Side Member
6. Clip and Bolt; Side Member
5. Clip and Bolt; Crossmember
Torque
N
⋅
m (kgf
⋅
m/lb
⋅
ft)
6 (0.6 / 4.3)
4. Retainer
3. Bolt
Torque
N
⋅
m(kgf
⋅
m/lb
⋅
ft)
16 (0.6 / 4.3)
2. Adjusting Nut
1. Lock Nut
•
Apply grease (BESCO L-2 or equivalent) to the front cable
contact portion.
•
Connect rear cable to the equalizer, then adjust the parking
brake. Refer to "SERVICING".
•
Tighten lock nut to the specified torque.
Torque
N
⋅
m(kgf
⋅
m/lb
⋅
ft)
16 (0.6 / 4.3)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст