Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Manual — part 251
ENGINE DRIVEABILITY AND EMISSIONS
6E–245
21
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the “SPS (Service Programming System)”.
Was the problem solved?
—
Verify repair
Go to Step 22
22
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual.
Following ECM programming, the immobiliser system
(if equipped) must be linked to the ECM. Refer to
section 11 “Immobiliser System-ECM replacement” for
the ECM/Immobiliser linking procedure.
—
Verify Repair
—
Step
Action
Value(s)
Yes
No
6E–246
ENGINE DRIVEABILITY AND EMISSIONS
DETONATION/SPARK KNOCK SYMPTOM
DEFINITIONS: A mild to severe ping, usually worse under acceleration. The engine makes a sharp metallic knocking
sound that changes with throttle opening. Prolonged detonation may lead to complete engine tailure.
Step
Action
Value(s)
Yes
No
1
Was the “On-Board Diagnostic (OBD) System Check”
performed?
—
Go to Step 2
Go to OBD
System Check
2
1. Perform a bulletin search.
2. If a bulletin that addresses the symptom is found,
correct the condition as instructed in the bulletin.
Was a bulletin found that addresses the symptom?
—
Verify repair
Go to Step 3
3
Was a visual/physical check performed?
—
Go to Step 4
Go to Visual /
physical Check.
4
1. If Tech 2 readings are normal (refer to Typical
Scan Data Values) and there are no engine
mechanical faults, fill the fuel tank with a known
quality gasoline.
2. Re-evaluate the vehicle performance.
Is detonation present?
—
Go to Step 5
Verify repair
5
1. Check for obvious overheating problems:
• Low engine coolant
• Restricted air flow to radiator
• Incorrect coolant solution
2. If a problem is found, repair as necessary.
Was a problem found?
—
Verify repair
Go to Step 6
6
Check the fuel pressure. Refer to Fuel System
Diagnosis.
Was a problem found?
—
Verify repair
Go to Step 7
7
1. Using a Tech 2, display the MAP sensor value in
comparison with atmosphere temperature.
2. Check for a faulty, plugged, or incorrectly installed
MAP sensor.
Was the problem found?
—
Verify repair
Go to Step 8
8
1. Using a Tech 2, display the ECT sensor and IAT
sensor value and warm up condition compared
with the typical data.
2. Check the specified value or wire.
Was the problem found?
—
Verify repair
Go to Step 9
9
Observe the throttle position display on the Tech 2
while slowly increasing throttle pedal.
Does the throttle position increase steady with
increasing smoothly?
—
Go to Step 10
Refer to
Diagnostic
Trouble Code
P0123 for
further
diagnosis
10
Check the knock sensor wire, shield wire, or
installation condition.
Was a problem found?
—
Verify repair
Go to Step 11
11
Check items that can cause the engine to run lean.
Refer to DTC P1171 “Fuel Supply System Lean
During Power Enrichment”.
Was a problem found?
—
Verify repair
Go to Step 12
ENGINE DRIVEABILITY AND EMISSIONS
6E–247
12
Check spark plugs for proper heat range.
Were incorrect spark plugs installed?
—
Verify repair
Go to Step 13
13
1. Remove excessive carbon buildup with a top
engine cleaner.
2. Re-evaluate vehicle performance.
Is detonation still present?
—
Verify repair
Go to Step 14
14
Check for an engine mechanical problem. Perform a
cylinder compression check. Refer to Engine
Mechanical.
Was a problem found?
—
Verify repair
Go to Step 15
15
1. Review all diagnostic procedures within this table.
2. If all procedures have been completed and no
malfunctions have been found, review/inspect the
following:
• Visual/physical inspection
• Tech 2 data
• All electrical connections within a suspected
circuit and/or system
Was a problem found?
—
Verify repair
Go to Step 16
16
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the “SPS (Service Programming System)”.
Was the problem solved?
—
Verify repair
Go to Step 17
17
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual.
Following ECM programming, the immobiliser system
(if equipped) must be linked to the ECM. Refer to
section 11 “Immobiliser System-ECM replacement” for
the ECM/Immobiliser linking procedure.
—
Verify Repair
—
Step
Action
Value(s)
Yes
No
6E–248
ENGINE DRIVEABILITY AND EMISSIONS
POOR FUEL ECONOMY SYMPTOM
DEFINITIONS: Fuel economy, as measured by an actual road test, is noticeably lower than expected. Also, economy
is noticeably lower than it was on this vehicle at one time, as previously shown by an actual road test.
Step
Action
Value(s)
Yes
No
1
Was the “On-Board Diagnostic (OBD) System Check”
performed?
—
Go to Step 2
Go to OBD
System Check
2
1. Perform a bulletin search.
2. If a bulletin that addresses the symptom is found,
correct the condition as instructed in the bulletin.
Was a bulletin found that addresses the symptom?
—
Verify repair
Go to Step 3
3
Was a visual/physical check performed?
—
Go to Step 4
Go to Visual /
physical Check.
4
Check owner’s driving habits.
• Is the A/C On full time (defroster mode On)?
• Are tires at the correct pressure?
• Are excessively heavy loads being carried?
• Is acceleration too much, too often?
—
Go to Step 5
Go to Step 6
5
Review the items in Step 4 with the customer and
advise as necessary.
Is the action complete?
—
System OK
—
6
Visually/physically check: Vacuum hoses for splits,
kinks, and improper connections and routing as
shown on the “Emission Control System Schematics”.
Was a problem found?
—
Verify repair
Go to Step 7
7
Check for low engine coolant level.
Was a problem found?
—
Verify repair
Go to Step 8
8
Check for incorrect or faulty engine thermostat. Refer
to Engine Cooling.
Was a problem found?
—
Verify repair
Go to Step 9
9
Remove and check the air filter element for dirt or for
restrictions.
Was a problem found?
—
Verify repair
Go to Step 10
10
1. Using a Tech 2, display the MAP sensor value in
comparison with atmosphere temperature.
2. Check for a faulty, plugged, or incorrectly installed
MAP sensor.
Was the problem found?
—
Verify repair
Go to Step 11
11
1. Using a Tech 2, display the ECT sensor and IAT
sensor value and warm up condition compared
with the typical data.
2. Check the specified value or wire.
Was the problem found?
—
Verify repair
Go to Step 12
12
Check the knock sensor wire, shield wire, or
installation condition.
Was a problem found?
—
Verify repair
Go to Step 13
13
Check the fuel pressure. Refer to Fuel System
Diagnosis.
Was a problem found?
—
Verify repair
Go to Step 14
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст