Isuzu Rodeo UE. Manual — part 476
TRANSMISSION CONTROL SYSTEM (4L30–E)
7A1–23
Intermittent Conditions
If the TECH–2 displays a diagnostic trouble code as
intermittent, or if after a test drive a DTC does not
reappear though the detection conditions for this DTC are
present, the problem is most likely a faulty electrical
connection or loose wiring. Terminals and grounds should
always be the prime suspect. Intermittents rarely occur
inside sophisticated electronic components such as the
PCM.
Use the DTC information to understand which wires and
sensors are involved.
When an intermittent problem is encountered, check
suspect circuits for:
1. Poor terminal to wire connection.
2. Terminals not fully seated in the connector body
(backed out).
3. Improperly formed or damaged terminals.
4. Loose, dirty, or corroded ground connections:
HINT: Any time you have an intermittent in more than
one circuit, check whether the circuits share a
common ground connection.
5. Pinched or damaged wires.
6. Electromagnetic Interference (EMI):
HINT: Check that all wires are properly routed away
from spark plug wires, distributor wires, coil, and
generator. Also check for improperly installed
electrical options, such as lights, 2–way radios, etc.
Use the F3: SNAPSHOT mode of the TECH–2 to help
isolate the cause of an intermittent fault. The snapshot
mode will record information before and after the problem
occurs. Set the snapshot to “trigger” on the suspect DTC
or, if you notice the reported symptom during the test
drive, trigger the snapshot manually.
After the snapshot has been triggered, command the
TECH–2 to play back the flow of data recorded from each
of the various sensors. Sign of an intermittent fault in a
sensor circuit is a sudden unexplainable jump in data
values out of the normal range.
Transmission and PCM Identification
The chart below contains a list of all important information
concerning rear axle ratio, Powertrain Control Module
(PCM), and transmission identification.
VEHICLE
Rr axle
Ratio
PCM
TRANSMISSION
Type
Engine
Ratio
ISUZU Parts No.
Calibration
Code
Isuzu Part No.
Model Code
Isuzu /
Rodeo
3.2L V6
4 100
8–09364–929–0
8 09364 959 0
G20
8–96018–004–3
FL (4
×
4)
Rodeo
4.100
8–09364–959–0
G20
8–96018–005–3
FM (4
×
2)
7A1–24 TRANSMISSION CONTROL SYSTEM (4L30–E)
Isuzu Rodeo
240RX004
TRANSMISSION CONTROL SYSTEM (4L30–E)
7A1–25
Diagnostic Trouble Code (DTC)
Identification
DTC
NUMBER
DTC NAME
DTC TYPE
MIL “CHECK
ENGINE”
“CHECK
TRANS”
P0218
Transmission Fluid Over Temperature
D
P0560
System Voltage Malfunction
D
P0705
Transmission Range Switch (Mode Switch) Illegal
Position
D
P0706
Transmission Range Switch (Mode Switch)
Performance
D
P0711
Transmission Fluid Temperature (TFT) Sensor
Circuit–Range/Performance
D
P0712
Transmission Fluid Temperature Sensor Circuit
Low Input (TFT)
D
P0713
Transmission Fluid Temperature (TFT) Sensor
Circuit High Input
D
P0719
TCC Brake Switch Circuit High (Stuck ON)
D
P0722
Transmission Output Speed Sensor (OSS) Low
Input
B
ON
Flash
P0723
Transmission Output Speed Sensor (OSS)
Intermittent
B
ON
Flash
P0724
TCC Brake Switch Circuit Low (Stuck OFF)
D
P0730
Transmission Incorrect Gear Ratio Flash
C
Flash
P0742
Torque Converter Clutch (TCC) Circuit Stuck ON
B
ON
Flash
P0748
Pressure Control Solenoid (PCS) (FORCE
MOTOR) Circuit Electrical
C
Flash
P0751
Shift Solenoid A Performance Without Input
Speed
B
ON
Flash
P0753
Shift Solenoid A Electrical
B
ON
Flash
P0756
Shift Solenoid B Performance Without Input
Speed
B
ON
Flash
P0758
Shift Solenoid B Electrical
B
ON
Flash
P1790
ROM Transmission Side Bad Check Sum
B
ON
Flash
P1792
EEPROM Transmission Side Bad Check Sum
B
ON
Flash
P1835
Kick Down Switch Always ON
D
P1850
Brake Band Apply Solenoid Malfunction
D
P1860
TCC Solenoid Electrical
B
ON
Flash
P1870
Transmission Component Slipping
B
ON
Flash
DTC TYPE
DEFINITION
B
Emission related, turn on MIL (Check Engine) and flashing Check Trans after 2 consecutive trips
with failure
C
Non–emission related, flashing Check Trans on 1st failure
D
Non–emission related, no lamps
NOTE: On the following charts, refer to Powertrain
Control Module (PCM) section for Wiring System and the
Body and Accessories section for circuit diagram details,
parts location, and connector configuration.
7A1–26 TRANSMISSION CONTROL SYSTEM (4L30–E)
DTC P0218 Transmission Fluid Over Temperature
D07RW018
Circuit Description
The Transmission Fluid Temperature (TFT) sensor is a
thermister that controls the signal voltage to the PCM.
The PCM supplies a 5–volt reference to the sensor on
circuit GRN/RED. When the transmission fluid is cold, the
sensor resistance is high and the PCM will sense high
signal voltage. As the fluid temperature warms to a
normal transmission operating temperature of 100
°
C
(212
°
F), the sensor resistance becomes less and the
voltage decreases to 1.5 to 2.0 volts.
This DTC detects a high transmission temperature for a
long period of time. This is a type “D” DTC.
Conditions For Setting The DTC
f
No TFT DTCs P0712 or P0713.
f
TFT is greater than 135
°
C (275
°
F).
f
All conditions met for 21 seconds.
Action Taken When The DTC Sets
f
Hot mode TCC Shift Pattern.
f
The PCM will not illuminate the Malfunction Indicator
Lamp (MIL).
f
ATF Lamp ON. (greater than 145
°
C (293
°
F))
f
Disable E–side TCC OFF request.
Conditions For Clearing The DTC
f
The DTC can be cleared from the PCM history by
using a scan tool.
f
The DTC will be cleared from history when the vehicle
has achieved 40 warm–up cycles without a failure
reported.
f
The PCM will cancel the DTC default actions when
the fault no longer exists and the ignition is cycled “off”
long enough to power down the PCM.
Diagnostic Aids
f
Inspect the wiring for poor electrical connections at
the PCM and at the transmission 16–way connector.
Look for possible bent, backed out, deformed or
damaged terminals. Check for weak terminal tension
as well.
Also check for a chafed wire that could short to bare
metal or other wiring. Inspect for a broken wire inside
the insulation.
f
When diagnosing for a possible intermittent short or
open condition, move the wiring harness while
observing test equipment for a change.
f
Check harness routing for a potential short to ground
in circuit GRN/RED.
f
Scan tool TFT sensor temperature should rise
steadily to about 100
°
C (212
°
F), then stabilize.
f
Check for a “skewed” (mis–scaled) sensor by
comparing the TFT sensor temperature to the
ambient temperature after a vehicle cold soak. A
“skewed” sensor can cause delayed garage shifts or
TCC complaints.
f
Check for a possible torque converter stator problem.
f
Verify customer driving habits, trailer towing, etc.
Test Description
The numbers below refer to the step numbers on the
diagnostic chart.
3. This test checks for a “skewed” sensor or shorted
circuit.
4. This test simulates a TFT DTC P0713.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст