Isuzu Rodeo UE. Manual — part 92
TRANSFER CASE
4D–31
Front Output Shaft Oil Seal Replacement
1. Remove the oil seal from the transfer case.
2. Apply engine oil to the oil seal outer surfaces.
3. Apply recommended grease (BESCO L2) or
equivalent to the oil seal lip.
4. Use the oil seal installer J–38594 to install the oil seal
to the transfer case.
220RW070
Legend
(50) Front Output Shaft Oil Seal
1. Install the transfer case (with oil seal) (42), performing
the following steps. (M/T)
f
Cover the shaft splines with adhesive tape (43).
This will prevent damage to the oil seal lip (44).
A07RW022
Legend
(43) Adhesive Tape
(44) Oil Seal Lip
(45) Oil Seal Collar
(46) Bearing
f
Apply recommended liquid gasket (LOCTITE FMD
127) or its equivalent to the transmission,
intermediate plate and transfer case fitting surfaces
(M/T).
220RS026
4D–32
TRANSFER CASE
Install the transfer case together with intermediate plate
with gear assembly to transmission case (M/T).
Tighten the transfer case bolts to the specified torque a
little at a time (M/T).
Torque : 37 N·m (27 lb ft)
2. Apply chassis grease (51) to the sub–gear (40) and
the counter gear (41) thrust surfaces.
226RW155
3. Install sub–gear (40) to counter gear (41).
4. Install belleville spring (39).
5. Install spacer.
6. Install ball bearing, using a bench press.
7. Select a snap ring that will allow the minimum axial
play.
Clearance : 0–0.1 mm (0–0.004 in)
Snap ring availability:
Thickness
Color–coding
1.50 mm (0.059 in)
White
1.55 mm (0.061 in)
Yellow
1.60 mm (0.063 in)
Blue
226RS170
226RS021
8. Use a pair of snap ring pliers to install the snap ring
(36) to the counter gear (41).
Sub–Gear (anti–lash plate) Preload
1. Hook a length of piano wire (52) over one of the
sub–gear (53) teeth.
2. Attach the other end of the piano wire (52) to a
spring balancer.
3. Measure the sub–gear preload.
Preload : 59–98 N (13–22 lb)
TRANSFER CASE
4D–33
226RW156
9. Install ball bearing (35), using a bench press.
10. Install snap ring (34).
11. Install the counter gear assembly (33) to the transfer
case (42).
12. Use a pair of snap ring pliers to install the snap ring
(32) to the transfer case (42).
NOTE: The snap ring must be fully inserted into the
transfer case snap ring groove.
13. Use a bench press to install the ball bearing (30) to the
front output shaft (31).
262RS012
14. Assemble the 2WD–4WD clutch hub and sleeve
assembly (28).
226RW140
15. Engage the springs in the same insert with the open
ends away from each other.
226RW141
4D–34
TRANSFER CASE
16. Install a new stopper plate (29) and the clutch hub and
sleeve assembly (28) to the front output shaft (31).
226RW157
Legend
(54) Front Output Gear
17. The clutch hub face (with the heavy boss) must be
facing the front output gear side.
18. Use a bench press to slowly force the clutch hub and
sleeve assembly (28) together with the stopper plate
(29) into place.
19. Align the inserts with the block ring insert grooves.
Install the block ring (27) to the clutch sleeve and hub
assembly (28).
20. Install the outside ring (26), inside ring (25) and
needle bearing (24) to the front output gear (23) and
bearing collar (18).
NOTE: Coat all parts with transmission oil before
installing them.
226RW139
21. Apply engine oil to the thrust surfaces of the
sub–gear, the belleville spring, and the spacer.
262RW014
22. Install sub–gear (anti–lash plate) (22), belleville
spring (21) and spacer (20). (M/T)
23. Install sub–gear snap ring (19). (M/T)
24. Use a bench press to install the needle bearing collar
together with the front output gear assembly, aligning
inside ring claw with block ring groove.
262RS014
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст