Isuzu KB P190. Manual — part 1342
8A-430 ELECTRICAL-BODY AND CHASSIS
REMOVAL AND INSTALLATION
This illustration is based on RHD
RTW780SH002601
DRIVER’S SIDE POWER WINDOW &
DOOR LOCK SWITCH
(2 DOOR MODELS)
Removal
1. Disconnect the battery ground cable.
2. Remove the screw in the pull cup with the tip of a
screwdriver.
3. Remove the switch bezel by pushing the spring with the tip
of a screwdriver.
4. Disconnect the connector.
ATTENTION:
When removing a switch bezel lift from the front in the
bezel.
It follows the front with the screwdriver.
The clip has broken when lifting from the rear in the bezel.
Installation
To install, follow the removal steps in the reverse order.
This illustration is based on RHD
RTW780SH002701
FRONT PASSENGER’S POWER WINDOW
SWITCH
(2 DOOR MODELS)
Removal
1. Disconnect the battery ground cable.
2. Removes the screw in the pull cup with the tip of a
screwdriver.
3. Remove the switch bezel by pushing the spring with the tip
of a screwdriver.
4. Disconnect the connector.
ATTENTION:
When removing a switch bezel lift from the front in the
bezel.
It follows the front with the screwdriver.
The clip has broken when lifting from the rear in the bezel.
Installation
To install, follow the removal steps in the reverse order.
ELECTRICAL-BODY AND CHASSIS 8A-431
This illustration is based on RHD
RTW780SH002601
DRIVER’S SIDE POWER WINDOW &
DOOR LOCK SWITCH
(4 DOOR MODELS)
Removal
1. Disconnect the battery ground cable.
2. Removes the screw in pull cup with the tip of a screwdriver.
3. Remove the switch bezel by pushing the spring with the tip
of a screwdriver.
4. Disconnect the connector.
ATTENTION:
When removing a switch bezel lift from the front in the
bezel.
It follows the front with the screwdriver.
The clip has broken when lifting from the rear in the bezel.
Installation
To install, follow the removal steps in the reverse order.
This illustration is based on RHD
RTW780SH002701
FRONT PASSENGER’S POWER WINDOW
SWITCH
(4 DOOR MODELS)
Removal
1. Disconnect the battery ground cable.
2. Removes the screw in pull cup with the tip of a screwdriver.
3. Remove the switch bezel by pushing the spring with the tip
of a screwdriver.
4. Disconnect the connector.
ATTENTION:
When removing a switch bezel lift from the front in the
bezel.
It follows the front with the screwdriver.
The clip has broken when lifting from the rear in the bezel.
Installation
To install, follow the removal steps in the reverse order.
8A-432 ELECTRICAL-BODY AND CHASSIS
RTW780SH002801
REAR POWER WINDOW & DOOR LOCK
SWITCH-LH & RH
Removal
1. Disconnect the battery ground cable.
2. Remove the screw in the pull cup with the tip of a
screwdriver.
3. Remove the switch bezel by pushing the spring with the tip
of a screwdriver.
4. Disconnect the connector.
ATTENTION:
When removing a switch bezel lift from the front in the
bezel.
It follows the front with the screwdriver.
The clip has broken when lifting from the rear in the bezel.
Installation
To install, follow the removal steps in the reverse order.
ELECTRICAL-BODY AND CHASSIS 8A-433
DRIVER’S SIDE POWER WINDOW
MOTOR
Removal
1. Window Regulator ASM
• Refer to the removal steps of the WINDOW
REGULATOR/POWER WINDOW MOTOR in Section
10 “BODY”.
2. Power Window Motor
• Loosen the fixing bolts to remove the power window
motor from the regulator.
Installation
To install, follow the removal steps in the reverse order.
FRONT PASSENGER’S POWER WINDOW
MOTOR
Removal
1. Window Regulator ASM
• Refer to the removal steps of the WINDOW
REGULATOR/POWER WINDOW MOTOR in Section
10 “BODY”.
2. Power Window Motor
• Loosen the fixing bolts to remove the power window
motor from the regulator.
Installation
To install, follow the removal steps in the reverse order.
RTW580SH002901
REAR POWER WINDOW MOTOR-LH &
RH
Removal and Installation
Refer to the “DRIVER’S SIDE POWER WINDOW MOTOR”
removal and installation steps in this section.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст