Isuzu KB P190. Manual — part 144
4C1-72 FRONT WHEEL DRIVE
ILLUSTRATION
PART NO.
PART NAME
9-8522-
1274-0
(J-24252)
Inner bearing outer race installer
5-8840-2085-0
(J-2
1777-42)
Pilot
5-8840-2089-0
(J-23597-9)
Nut & bolt
5-8840-2087-0
(J-23597-7)
Gauge plate
5-8840-0
126-0
(J-800
1)
Dial indicator
5-8840-0
128-0
(J-23597-
1)
Arbor
5-8840-2088-0
(J-23597-8)
Disc (2 pcs. required)
9-8522-
1165-0
(J-6
133-01)
Pinion bearing installer (for 4WD)
9-8522-
1275-0
(J-24250)
Pinion oil seal installer
FRONT WHEEL DRIVE 4C1-73
ILLUSTRATION
PART NO.
PART NAME
9-8522-
1164-0
(J-24244)
Side bearing installer
5-8840-2852-0
Outer bearing installer
(for 2WD)
5-8522-0054-0
(J-290
15)
Inner bearing installer
(for 4WD)
5-8840-2853-0
Hub oil seal installer
(for 2WD)
5-8840-2
117-0
(J-36827)
Hub nut wrench
5-8840-2
119-0
(J-36829)
Inner bearing installer (for 4WD)
5-8840-2854-0
Oil seal installer (for 4WD)
5-8840-2789-0
ABS sensor rotor installer
9-8522-
1270-0
Inner bearing installer (for 2WD)
SHIFT ON THE FLY SYSTEM 4C2
SECTION 4C2
SHIFT ON THE FLY SYSTEM
TABLE OF CONTENTS
Service Precaution . . . . . . . . . . . . 4C2-1
Shift On The Fly System . . . . . . . . . 4C2-2
Outline of Shift on The Fly System. . . . .. 4C2-2
Shift On The Fly Electrical Equipment. . . . 4C2-3
Axle Shaft Connection and Disconnection . .. 4C2-3
Actuator Assembly . . . . . . . . . . .. 4C2-3
Shift On The Fly System and Association
Parts . . . . . . . . . . . . . . . . .. 4C2-4
Disassembly. . . . . . . . . . . . . 4C2-5
Inspection and Repair . . . . . . . . . . 4C2-6
Reassembly . . . . . . . . . . . . . 4C2-9
Torque Specifications. . . . . . . . . ..4C2-12
Special Service Tool . . . . . . . . . ...4C2-13
SHIFT ON THE FLY SYSTEM 4C2-1
SERVICE PRECAUTION
WARNING: THIS VEHICLE HAS A SUPPLEMENTA L
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFER
TO THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN
POSSIBLE AIR BAG DEPLOYMENT, PERSONAL
INJURY, OR OTHERWISE UNNEEDED SRS SYSTEM
REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU/GM will call out those fasteners that require
a replacement after removal. ISUZU/GM will also
call out the fasteners that require thread lockers or
thread sealant. UNLESS OTHERWISE SPECIFIED,
do not use supplemental coatings (Paints, greases,
or other corrosion inhibitors) on threaded fasteners
or fastener joint interfaces. Generally, such
coatings adversely affect the fastener torque and
the joint clamping force, and may damage the
fastener. When you install fasteners, use the
correct tightening sequence and specifications.
Following these instructions can help you avoid
damage to parts and systems.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст