Isuzu KB P190. Manual — part 934

Powertrain Interface Module – V6

Page 6E1–75

N O T E

The Tech 2 PIM Security Information Data List
typical display values are obtained from a
correctly operating vehicle under the following
conditions:
• ignition switched on,
• engine not running, and
• vehicle is stationary.

Tech 2 Parameter

Units Displayed

Typical Display Values

ICU / PIM Status

Yes / No

Yes

Security Code Programmed

Yes / No

Yes

Security Wait Time

Inactive / Active

Inactive

Security Wait Time

Inactive / 0:00:00

Inactive

Security Code Correct Enter

Yes / No

Yes

Security Code Reset Counter

0

0

12.2 PIM Reset Procedure

Do not perform the reset procedure within
sixty seconds of turning the ignition switch
on. Failure to comply may result in the PIM
failing to reset.

When a PIM has been installed into a vehicle, it is security linked to the immobiliser control unit (ICU) and engine control
module (ECM). Once this linking has been performed, the PIM cannot be installed in any other vehicle, unless the
security linking between the ICU and the ECM has been reset using the following procedure:

1

Prior to resetting the PIM, obtain the Security Code. For further information, refer to 12.1

Security and

Programming Information.

2

Connect Tech 2 to the data link connector (DLC) and turn the ignition switch on.

3

On Tech 2 select: Body / Powertrain Interface Module / Security / Reset PIM.

N O T E

When Tech 2 requests programming approval,
obtain TIS approval.

N O T E

If a Tech 2 screen displaying Security Wait Time
Active, Please Wait! appears after selecting the
Reset PIM option, an incorrect security code has
been previously entered. Refer to 12.1
Security and Programming Information for further
information.

4

When Tech 2 displays Enter Security Code, enter the security code, press the Enter key and then the Okay soft
key.

The engine will not start after the PIM has
been reset.

5

When Tech 2 displays Do you really want to Reset?, press the Reset soft key.

Powertrain Interface Module – V6

Page 6E1–76

Do not turn the ignition switch off within 60
seconds of performing the PIM reset
procedure. Failure to comply may result in the
PIM failing to reset.

6

When Tech 2 displays Reset Completed Successfully, press the Confirm soft key to return to the Tech 2
Security screen.

12.3 PIM

Configuration

Configuring the PIM

Programming Transmission Variant

1

Connect Tech 2 to the data link connector (DLC).

2

On Tech 2 select: Body / Powertrain Interface Module / Program / Program Variant Configuration.

3

Press the Modify soft key.

4

Using the up or down arrow selection keys, select either manual or automatic transmission.

5 Press

the

Confirm soft key. Tech 2 reverts to the main Tech 2 Program Variant Configuration screen where the

selection made in the previous step is displayed.

6 Press

the

Program soft key. The changes are now programmed into the PIM.

Do not turn the ignition switch off within 60
seconds of configuring the PIM. Failure to
comply may result in the changes failing to be
programmed into the PIM.

7

When notified that the programming was successful, press the Confirm soft key to return to the Tech 2 Program
screen.

Programming the VIN

1

Connect Tech 2 to the data link connector (DLC).

2

On Tech 2 select: Body / Powertrain Interface Module / Program / Program VIN.

3

Enter the VIN using the Tech 2 arrow selection keys.

N O T E

The left and right arrow selection keys move the
Tech 2 cursor along the VIN number, whilst the
up and down selection arrows change the
character value.

Numbers can also be entered by pressing the
number key's on Tech 2.

4

After entering the VIN number, press the Enter key. The changes are now programmed into the PIM.

Powertrain Interface Module – V6

Page 6E1–77

Do not turn the ignition switch off within 60
seconds of programming the VIN. Failure to
comply may result in the changes failing to be
programmed into the PIM.

5

When notified that the programming was successful, press the Confirm soft key to return to the Tech 2 Program
screen.

12.4 Immobiliser Link to ECM / PIM

Do not perform the Immobiliser Link to ECM /
PIM procedure within sixty seconds of turning
the ignition switch on. Failure to comply may
result in the PIM failing to link.

When the powertrain interface module (PIM) has been replaced, it is necessary to security link the PIM to the immobiliser
control unit (ICU) and engine control module (ECM) before the vehicle will start.

N O T E

This linking procedure between the ECM and PIM
is also known as the Immobiliser Function
Programming.

1

Prior to performing the linking procedure, obtain the security code. For further information, refer to 12.1Security
and Programming Information.

2

Connect Tech 2 to the data link connector (DLC).

3

On Tech 2 select: Body / Powertrain Interface Module / Security / Immobiliser Link to ECM / PIM.

4

When Tech 2 displays Immobiliser Replaced, press the No soft key.

5

When Tech 2 displays PIM or ECM Replaced?, press the Yes soft key.

N O T E

When Tech 2 requests programming approval,
obtain TIS approval.

6

When Tech 2 displays Enter Security Code, enter the security code and press the Enter key and then the Okay
soft key.

7

When Tech 2 displays Confirm Security Code, re-enter the security code, press the Enter key and then the Okay
soft key.

8

When Tech 2 displays Select Immobiliser Programming Routine, use the up or down arrow selection keys, to
select the PIM Replaced option and press the Enter key.

9

When Tech 2 displays Stop Engine – Turn Off Ignition, turn the ignition switch off and press the Confirm soft key.

10

When Tech 2 displays Turn Ignition On, turn the ignition switch on and press the Confirm soft key.

Powertrain Interface Module – V6

Page 6E1–78

Do not turn the ignition switch off within 60
seconds of performing the ICU Link to

ECM / PIM procedure. Failure to comply may
result in the PIM failing to link with the

ICU / ECM.

11

When Tech 2 displays Programming Successful, press the Confirm soft key to return to the Tech 2 Security
screen.