Isuzu engine 4j series. Manual — part 42
6A1 – 36 4JB1/4JB1T/4JB1TC/4JG2 - ENGINE
3. Power Steering Pump Drive Belt (P/S pump model)
•
Install PS pump drive belt and adjust belt tension.
•
Depress the drive belt mid-portion with a 98N
(10kg/22lb) force.
Drive Belt Deflection
mm (in)
8 (0.31) - 12 (0.47)
•
Tighten the idler lock nut to the specified torque.
N∙m (kg∙m/lb∙ft)
27 (2.8/20)
2. Fan Shroud
•
Install the fan shroud and reservoir tank hose.
1. Cooling Fan Assembly
•
Mount fan pulley, distance piece, and cooling fan asm
(in this order) on the water pump, and tighten to the
specified torque.
N∙m (kg∙m/lb∙in)
8 (0.8/69)
•
Connect battery ground cable.
•
Pour coolant.
•
Start the engine and check coolant leakage.
6A1-36-1.tif
4JB1/4JB1T/4JB1TC/4JG2 – ENGINE 6A1 – 37
CYLINDER HEAD ASSEMBLY AND GASKET
REMOVAL
Preparation:
•
Disconnect battery ground cable.
•
Drain coolant from the radiator and engine.
1. Radiator Hose Upper
•
Disconnect upper radiator hose from engine side.
6A1-37-1.tif
Removal steps
1. Radiator hose upper
2. Heater hose
3. A/C Compressor drive
belt
4. Engine harness
5. Air intake duct
6. Injection pipe
7. Leak off pipe
8. PCV hose
9. Glow plug harness
10. Oil level gauge guide
tube
11. Oil cooler water pipe
12. A/C Compressor
Assembly
13. Vacuum actuator hose
14. Front exhaust pipe
15. By-pass hose
16. Cylinder head cover
17. Rocker arm shaft
18. Push rod
19. Cylinder head
Assembly
20. Cylinder head gasket
Installation steps
To install, follow the
removal steps in the
reverse order.
6A1 – 38 4JB1/4JB1T/4JB1TC/4JG2 - ENGINE
2. Heater Hose
•
Disconnect heater hose from heater pipe.
3. A/C Compressor Drive Belt
•
Loosen idler lock nut.
•
Loosen adjust bolt and remove drive belt.
4. Engine Harness
•
Disconnect harness connectors from units on
thermostat housing.
5. Air Intake Duct
•
Remove the clip and air intake duct.
6. Injection Pipe
•
Release injection pipe clip.
•
Remove flare nut injection pump side.
•
Remove flare nut injection nozzle side and remove
injection pipe.
NOTE:
Plug the injection nozzle holder and the delivery
holder to prevent the entry of foreign matters into
them.
7. Leak Off Pipe
•
Remove the leak off pipe side of leak off hose.
8. PCV Hose
•
Remove the PCV hose from air intake pipe.
6A1-38-1.tif
6A1-38-2.tif
4JB1/4JB1T/4JB1TC/4JG2 – ENGINE 6A1 – 39
9. Glow Plug Harness
10. Oil Level Gauge Guide Tube
•
Remove the guide tube from cylinder head.
11. Oil Cooler Water Pipe (Oil Cooler Model)
•
Remove the pipe fixing bolt of cylinder head rear side.
•
Remove the oil cooler water pipe fixing nut from inlet
manifold.
12. A/C Compressor Assembly (A/C Model)
•
Remove the clutch harness connector.
•
Remove the A/C compressor fixing bolts and
temporally tighten the A/C compressor to chassis
frame side use the wire.
13. Vacuum Actuator Hose (Exhaust Brake Model)
•
Remove the vacuum hoses from vacuum actuator.
14. Front Exhaust Pipe
•
Remove the exhaust pipe fixing bolts from exhaust
manifold.
•
Remove the exhaust pipe stay bolt.
6A1-39-1.tif
6A1-39-2.tif
6A1-39-3.tif
6A1-39-4.tif
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст