Isuzu N-Series. Manual — part 1289
If the parking brake handle still travels more than the standard value, then use
the adjusting nuts to adjust the length of the parking brake cable.
(1) Loosen the locknut.
(2) Use adjusting nut and adjusting bolt to adjust the length of the parking brake
cable.
(3) Tighten the adjusting nut, and lock it with locknut.
Tire replacement in rotation
In order to keep an even abrasion degree of all the wheel tires and to prolong
their service life, the front and rear tires should be exchanged in their positions
in the order shown in the figure.
Exchange the tires every 9000km.
130
OWNER爷S MANUAL
JAC High end Light Trucks
Inflation pressure of tires
The standard inflation pressure for the tires: 670kPa
The tire pressure check and their maintenance should be done at the time
when they are in cold state (over 3 hours parking or less than 1.6km running).
It is mandatory to keep a tire inflation pressure value up to the requirement.
For the trucks with dual wheels as the two-tire rear wheels, it will suffice to use
general inflating valve spanner to help measure the air pressure of the tires on
the inner side.
131
Plug-in fuse
Starter
132
Insert type fuse
If the head lights or other elements cannot work but the fuse is OK, then you
should check the insert type fuse. If it is already melt broken, change for a new
one. A JAC insert type fuse must be used for the change.
No steel wire is allowed to be used, even if it is temporary use. It will bring
about great damage or even fire.
License light
Screw off the fixing bolts before taking down the glass.
OWNER爷S MANUAL
JAC High end Light Trucks
Fuse in-place tag
Roof light and interior mirror
The lampshade can be simply taken out by hand, and then take down the bulb.
Fuse box
The fuse box is located under glove compartment. Open the fuse box and you
can check and replace the fuse. The box cover can be pulled out by hand.
Please use a pair of nipper pliers to change the fuse.
133
schematic of different fuse installation
15A 10A 15A 15A 15A 15A 20A 15A 15A 30A
15A 20A 30A 20A 15A 20A 15A 15A 10A 30A
Normal
broken
If the fuse is found broken, check and try to find out the reason for that. Take
necessary maintenance measures before fuse replacement.
Before changing the fuse, turn the start switch to "LOCK" position, and must
use fuses of the same current rating.
134
OWNER爷S MANUAL
JAC High end Light Trucks
Front light set
When replacing bulbs, take down the cover first, then the decoration bands for
the headlights screw off the 4 screws, and the bulbs can be taken out.
Rear light set
When replacing the bulbs, you have to take down the tail light before taking out
the bulb from behind the tail light.
Non-return reflector
Turn signal light
Brake light
Rear light
Rear fog light
Reverse light
135
136
Battery electrolyte level
The battery electrolyte level should be between the upper and lower scale
marks. If the level is too low, it is necessary to add more distilled water.
Headlights
Properly adjust the headlights, to ensure adequate illumination level on the
highways and no dazzle lighting to drivers in other vehicles head-on. When you
need to adjust the headlights, you'd better contact the authorized JAC service
stations that have special equipment.
The headlights' lighting
Tighten the Screw A for vertical adjustment, and tighten Screw B for horizontal
adjustment.
OWNER爷S MANUAL
JAC High end Light Trucks
User
Power(W)
User
Power(W)
User
Power(W)
Front windshield wiper
60
Rear fog light
25
Brake light
25伊2
Front fog light
55伊2
High beam
60伊2
Low beam
55伊2
Reverse light
20伊2
CD set
80
Electric horn
42
Marker light
10伊5
Blower
120
Turn signal light
21伊4
Ceiling light
10
Instruments
70
Others
30
Replacement of bulbs
The removable parts of all lamps are illustrated respectively for reference.
The switches must be turned off when replacing the bulbs and only bulbs of the same rating can be used. The standard
bulb ratings are listed below:
137
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст