Isuzu N-Series. Manual — part 221
HYDRAULIC BRAKES 5A-43
4. Correct any areas having poor contact with sand-
paper.
5. Repeat Steps 1 through 4 until the contact between
the brake lining and the brake drum is perfect.
Installation
1. Back Plate
Tighten the back plate bolts to the specified torque.
* Single Tire models
** Dual Tire models
2. Wheel Cylinder Assembly
Tighten the wheel cylinder assembly bolts to the
specified torque.
Back Plate Bolt Torque
N
⋅m (kg⋅m/lb⋅ft)
Drum Inside
Dia. mm (in)
Lining
Width mm (in)
—
228.6 (9.00)
75 (2.95)
108 (11.0/80)
240.0 (9.45)
60 (2.36)
108 (11.0/80)
260.0 (10.24)
90 (3.54)
108 (11.0/80)
279.4 (11.00)
60 (2.36)
74 (7.5/54)
290.0 (11.42)
75 (2.95)
108 (11.0/80)
300.0 (11.81)
75 (2.95)
* 44 (4.5/33)
** 108 (11.0/80)
320.0 (12.60)
75 (2.95)
108 (11.0/80)
100 (3.94)
108 (11.0/80)
120 (4.72)
157 (16.0/116)
N5A0142E
Wheel Cylinder Assembly Bolt Torque
N
⋅m (kg⋅m/lb⋅ft)
Drum Inside
Dia. mm (in)
Lining
Width mm (in)
—
228.6 (9.00)
75 (2.95)
34 (3.5/25)
240.0 (9.45)
60 (2.36)
25 (2.5/18)
260.0 (10.24)
90 (3.54)
43 (4.4/32)
279.4 (11.00)
60 (2.36)
27 (2.8/20)
290.0 (11.42)
75 (2.95)
25 (2.5/18)
300.0 (11.81)
75 (2.95)
34 (3.5/25)
320.0 (12.60)
75 (2.95)
43 (4.4/32)
100 (3.94)
74 (7.5/55)
120 (4.72)
94 (9.6/69)
N5A0173E
N5A0146E
5A-44 HYDRAULIC BRAKES
3. Brake Pipe
Tighten the brake pipe flare nuts to the specified
torque.
Tighten:
Brake pipe flare nuts to 16 N
⋅m (1.6 kg⋅m / 12 lb⋅ft)
Notice:
Take care not to twist the piping.
4. Brake Shoe and Return Spring
1) Before setting the brake shoes, apply a thin
coat of molybdenum disulfide grease to the
back plate portions (1) contacting the brake
shoe edge as shown in the illustrations.
2) Apply a coat of molybdenum disulfide grease to
the wheel cylinder parts contacting the brake
shoe (2).
3) Set the brake shoe assembly to the cylinder ad-
justing screw at the brake shoe small angle
end.
Do not install it at the round end.
4) Install the brake shoes and the return springs to
the wheel cylinders.
Keep the brake lining clean.
5. Shoe Holding Spring, Cup and Pin
1) Before installing the holding pin.
Apply a coat of molybdenum disulfide grease to
the holding cup seating faces (1) contacting the
brake shoe.
2) After installation of the pins, cups and the
springs, make sure the pin (2) seats to the cup
(3) properly.
6. After installation of brake drum, be sure to perform
the preload adjustment of hub bearing.
7. Bleed the air from brake.
With Auto-adjuster
For the drum brake with auto-adjuster, perform the fol-
lowing procedure before Step 6 and 7.
1. Measure the internal diameter of the brake drum.
• Take measurement of the distance at (A), (B)
and (C) points.
N5A0147E
N5A0150E
N5A0151E
N5A0152E
HYDRAULIC BRAKES 5A-45
2. Measure the external diameter of the brake shoe.
• Take measurement of the distance at (A), (B)
and (C) points.
3. Turn the adjuster gear so that the difference be-
tween the internal diameter of the brake drum and
the internal diameter of the brake shoe becomes
0.6 mm (0.024 in).
4. Install the brake drum.
Adjustment
Without Auto-adjuster
Turn the adjuster until the brake drum stops rotating.
Depress the brake pedal several times and turn the ad-
juster furthermore. When the brake drum stops rotating
completely, turn the adjuster back for 5 to 6 notches.
With Auto-adjuster
Strongly depress the brake pedal several times while ro-
tating the brake drum in the direction of moving forward
or driving the vehicle forward. This adjusts the brake
drum clearance automatically.
N5A0003E
N5A0004E
5A-46 HYDRAULIC BRAKES
Rear Drum Brake Assembly (Drum Inside Diameter 370 mm)
Removal
• Block vehicle wheels and apply the parking brake.
• Raise the axle to clear the tire from the ground. Po-
sition jack stands under vehicle.
1. Wheel and tire assembly and brake drum and hub
assembly.
• Refer to Section 3E WHEELS AND TIRES.
• Refer to Section 4C FRONT AXLE and Section
3C FRONT SUSPENSION.
• Refer to Section 4B REAR AXLE.
2. Holder nuts.
3. Shoe return springs using a return spring plier.
Return spring plier: 9-8522-0026-0
4. Shoe and lining assemblies.
5. Brake pipes.
Notice:
The brake pipes to the wheel cylinders must be removed
before the wheel cylinders can be removed.
6. Brake hose.
7. Back plate.
8. Wheel cylinders.
Legend
1. Cotter pin
5. Wheel cylinder assembly
2. Shoe hold nut
6. Back plate
3. Brake shoe return spring
7. Brake pipe
4. Brake shoe assembly
7
1
2
3
3
4
5
6
N5A0464E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст