Isuzu N-Series. Manual — part 873
7B1-16 MANUAL TRANSMISSION (MZZ)
17. Use the remover (5-8840-0027-0) and the sliding
hammer (5-8840-0084-0) to remove the neutral
bearing (main end) from the rear cover.
18. Remove the relay lever 6th gear (1).
19. Use a spring remover to force out the spring pins
(2) from the 6th gear shift arm (3) and the 6th gear
shift rod (4).
20. Remove the 6th gear shift arm and the 6th gear
shift rod.
21. Use a pair of snap ring pliers to remove the snap
ring from the 6th gear clutch hub.
22. Use a puller to remove the 6th gear clutch hub as-
sembly, the sleeve, the block ring, the gear, and
the needle bearing from the counter shaft.
23. Disassemble the 6th gear clutch hub assembly and
the sleeve.
24. Remove the speedometer gear.
25. Remove the retainer from the transmission case.
26. Pull out the reverse idle shaft.
27. Remove the reverse idle gear together with the
needle bearing.
5-8840-0084-0
5-8840-0027-0
N7A0348E
N7A1140E
Legend
1. Clutch hub
2. Sleeve
3. Ball
4. Block
5. Spring
N7A1141E
1
5
4
3
2
N7A0372E
MANUAL TRANSMISSION (MZZ) 7B1-17
28. Remove the snap ring (rear outer) from the main
shaft rear bearing.
29. Remove the shim from the counter shaft rear bear-
ing.
30. Remove the snap rings (4th / 5th and 6th shift
rods).
31. Remove the transmission case from the clutch
housing.
32. Remove the bearing rear outer race from the trans-
mission case.
33. Use a spring pin remover to remove the spring pins
from the 4th / 5th shift rod, the 1st / reverse shift
block, the 6th shift block, and 4th / 5th shift arm.
34. Remove the 4th / 5th shift rod, the 1st / reverse shift
block, the 6th shift block, and 4th / 5th shift arm.
Caution:
To avoid damaging other parts, place a round shaft at
the opposite end of the shift rod when removing the
spring pins.
35. Remove the 1st / reverse and the 2nd / 3rd shift
rod, the 1st / reverse shift arm, the 2nd / 3rd shift
arm, the 1st / reverse, and the 6th shift block.
Caution:
To avoid damaging other parts, place a round shaft at
the opposite end of the shift rod when removing the
spring pins.
N7A1090E
N7A0353E
N7A0316E
N7A1147E
7B1-18 MANUAL TRANSMISSION (MZZ)
36. Use the remover (5-8840-2755-0) to remove the
bush from the 4th / 5th shift arm.
37. Use the remover (5-8840-2755-0) to remove the
bush from the 1st / reverse shift arm.
38. Use the remover (5-8840-2755-0) to remove the
bush from the 2nd / 3rd shift arm. from the 1st / re-
verse shift arm.
Caution:
To avoid damaging other parts, place a round shaft at
the opposite end of the shift arm (same length as the re-
mover) when removing the bushes.
39. Remove the magnet from the clutch housing.
40. Remove the main shaft assembly, upper gear shaft
assembly, and the countershaft assembly.
a. Tightly wrap belts such as lashing belts around
the main shaft assembly, upper gear shaft as-
sembly, and the countershaft assembly in two
or more places to prevent the assemblies from
separating.
b. Secure the bearing remover to the main shaft
with the lock nut, then raise it with a hoisting ca-
ble. Spread the outer snap ring of the upper
gear shaft bearing, which is attached to the
clutch housing, and simultaneously remove up-
per gear shaft assembly, main shaft assembly,
and countershaft assembly from the clutch
housing.
N7A1148E
N7A1094E
N7A1095E
N7A0356E
MANUAL TRANSMISSION (MZZ) 7B1-19
41. Inspect the clutch housing bush for wear and dam-
age. If wear or damage is present, the bush must
be replaced. Remove the old bush from the clutch
housing with a pair of pliers.
42. Inspect the front oil seal for wear and damage. If
wear or damage is present, the seal must be re-
placed. Remove the old seal from the clutch hous-
ing with an ordinary screwdriver.
43. Inspect the other parts for wear and damage. If
wear or damage is present, make the necessary
repairs or replace the part(s).
44. Inspect the shift rod and the shift arm (shift mech-
anism) for bending, wear, and other damage. If mi-
nor wear or damage is present, make the
necessary repairs. If major wear or damage is
present, the part(s) must be replaced.
45. Use a micrometer to measure the shift arm end
thickness. If the thickness exceeds the specified
limit, the shift arm must be replaced.
46. Inspect the speedometer driven gear and the driv-
en gear bush for wear and other damage. Replace
the driven gear and bush if significant wear is
present.
Reassembly
1. Inspect the oil seal for wear and damage. If dam-
age or wear is present, the seal must be replaced.
2. Apply engine oil (5W-30) to the outside circumfer-
ence of the oil seal.
3. Apply multi-purpose type grease to the lipped por-
tion of the oil seal.
N7A1097E
N7A1098E
Shift arm end thickness
mm (in)
Gear
Standard
Limit
1st / reverse
3rd / 2nd
5th / 4th
9.60 — 9.85
(0.378 — 0.388)
9.00
(0.354)
6th
9.60 — 9.85
(0.378 — 0.388)
9.30
(0.366)
N7A1100E
N7A1101E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст