Isuzu N-Series. Manual — part 472
6G-8 TURBOCHARGER
Exhaust Manifold
Component
Removal
1. Turbocharger as outlined previously in this section.
2. Heat shield
3. Loosen the exhaust manifold bolts, nuts and wash-
ers in numerical order shown in the illustration.
4. Exhaust manifold
5. Gaskets
Caution:
• Exhaust manifold and cylinder head for cracks or
damage to gasket surfaces.
Installation
1. Gaskets.
2. Exhaust manifold.
3. Washers nuts and bolts.
Tighten:
Exhaust manifold to 34 N
⋅m (3.5 kg⋅m/ 25 lb⋅ft)
4. Heat shield
5. Turbocharger as outlined previously in this section.
Turbocharger Turbine Housing Replace-
ment (For 4HG1-T Model)
Changing the turbine housing of the turbocharger
(integrated with the exhaust manifold)
Inspection
Before replacing the turbine housing, make sure there
are no abnormalities in other parts.
Legend
1. Heat shield
4. Exhaust manifold
2. Exhaust adapter
5. Exhaust manifold gasket
3. Turbocharger
N6A1600E
N6A1683E
TURBOCHARGER 6G-9
Notice:
• It is normal to find some oil inside the compressed-
air duct. The oil is to lubricate the turbine shaft, and
as long as the exhaust is not abnormally white in
color, this does not indicate a problem.
1. Make sure the parts have no cracks, impeded
movement, damage, or distortion of shape, that
there is no oil leakage from the seal, and that there
is no gas leakage.
2. Turn the rotor to see if it rotates smoothly, also
checking the rotation direction as well as the
amount of slack.
Refer to the separate reference sheet for the prop-
er amount of slack.
If there is an abnormality in any of the above, you
will have to change the turbocharger as a unit.
Disassembly
1. Separate the end of the actuator rod (1) from the E
Ring (2), then remove the crank (3) from the end of
the rod (1).
2. Remove the turbine housing tie-down bolts (7).
3. Separate the turbine housing from the sensor
housing.
Notice:
• Be careful not to scratch the turbine blades when
removing parts.
Inspecting the center housing assembly:
Check that none of the blades is bent, cracked, or
scratched. Make sure there are no obstructions that
would interfere with the movement of the blades or with
mounting the new housing. Remove any excess carbon
or oil.
Replacing Parts
When reassembling, be sure to replace the following
parts. (Use only genuine Isuzu parts.)
1. E Ring (2)
2. Turbine housing tie-down bolts (7)
3. Turbine housing clamp (6)
4. Adapter nut (4)
5. Adapter stud (5)
Legend
1. Compressor port
N6A1385E
N6A1386E
N6A1386E
6G-10 TURBOCHARGER
Cleaning
Thoroughly clean off the oil and carbon from abutting
surfaces, the oil passages, flange surfaces, air and ex-
haust ducts, etc. Always air-dry the parts after cleaning.
Assembly
1. Insert the sensor housing into the turbine housing.
Notice:
• When inserting the sensor housing, make sure it
will not impede the movement of the turbine
blades.
2. Apply molybdenum disulfide to the thread and un-
derside of the head of each bolt (1).
3. Temporarily secure the sensor housing in place
with the clamp (2).
4. Connect the oil side of the sensor housing (1) and
the EGR-connection side of the exhaust manifold
(2) to the angle setting gauge, then tighten the bolt
to secure the gauge in place. (The angle of the
sensor housing and turbine housing will be set with
the use of this gauge).
Turbocharger housing setting gauge: 5-8840-2673-0
(1) M6
× P = 1.00
(2) M8
× P = 1.25
5. To give the sensor housing some slack, loosen the
bolt on side (1) by half a turn.
6. Tighten the turbine housing tie-down bolts to the
specified torque.
Tighten:
Housing tie-down bolts to 22 N
⋅m (2.2 kg⋅m/ 16 lb⋅ft)
7. Remove the bolt that secures the pressure gauge,
then remove the gauge.
8. Manually turn the rotor clockwise to be sure it it ro-
tates smoothly. Check for abnormal noise, drag,
etc.
9. Attach the end of the actuator rod (1) to the crank
at the waste gate (3), and secure with the E Ring
(2).
10. (Indicate on the nameplate that parts were re-
placed.)
N6A1388E
N6A1389E
N6A1386E
TURBOCHARGER 6G-11
11. Pour clean oil through the oil filler port to prevent
corrosion.
12. Seal the air and exhaust ducts of the turbocharger,
as well as the water and oil filler ports to prevent
foreign matter from entering.
Follow the assembly directions to reattach to the engine.
N6A1391E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст