Isuzu N-Series. Manual — part 1155
8-332 CAB AND CHASSIS ELECTRICAL
Installation
To install, follow the removal steps in the reverse order.
Warning Light Bulb, Indicator Light Bulb and Il-
lumination Light Bulb
Removal
Preparation:
Disconnect the battery ground cable.
1. Meter Assembly
Refer to “METER ASSEMBLY” in this section.
2. Socket and Bulb
Hold the bulb socket by hand and rotate it counter-
clockwise to remove them from the meter body.
3. Bulb
Pull out the bulb from the socket.
Installation
To install, follow the removal steps in the reverse order.
Vehicle Speed Sensor
The vehicle speed sensor is installed on the rear portion
of the transmission or transfer case.
The number of pulses generated is four pulses per one
rotation of the pinion shaft.
Inspection
1. Connect a resistance of 390
Ω±5%, 2W between
connector terminal 1
and battery (+) terminal
and connect the connector terminal 2
to the
battery (
−) terminal.
Caution:
Be extremely careful not to connect the battery (+) ter-
minal to the connector 3
.
This may damage the vehicle speed sensor.
2. Rotate the shaft of the vehicle speed sensor slowly
and measure the voltage between 3
and 2
with a digital tester.
The voltage, with one rotation of shaft, fluctuates four
times in the following range: 10 to 14V
↔ 24 or less.
Replace the sensor when the result of inspection is
found abnormal.
Legend
1. Meter Assembly
2. Meter Glass
3. Meter Plate
4. Warning Lens
N8A0344E
N8A0345E
J-32
J-32
J-32
J-32
J-32
CAB AND CHASSIS ELECTRICAL 8-333
Removal
Preparation:
Disconnect the battery ground cable.
1. Vehicle Speed Sensor
Disconnect the connector.
Installation
1. Tighten the vehicle speed sensor to the specified
torque.
Tighten:
Vehicle speed sensor to 25 N
⋅m (2.5 kg⋅m/18 lb⋅ft)
Caution:
Tightening must be made at the hexagonal part of the
sensor.
To tighten the connector itself would cause damage.
Thermo Unit
Inspection
The thermo unit is thermistor type and must be inspect-
ed under the conditions as shown below.
1. Put the deviation of the galvanometer to 0 by using
the variable resistor, switch the thermo unit off and
then measure the resistance of the resistor through
the bridge.
Confirm that the resistance is continuously variable
in any other points than those shown below.
2. Dip the thermo unit into 80 — 90
°C (176 — 194°F)
water and confirm that there is no bubble continu-
ously coming out of inside of the unit.
Replace the unit when the result of inspection is
found abnormal.
Oil Pressure Switch
Inspection
Check the continuity between the switch terminal and
the body ground with the starter switch is OFF position.
Replace the switch when the result of inspection is
found abnormal.
N8A0346E
Parking brake drum
Connector
N8A5408E
N8A5409E
8-334 CAB AND CHASSIS ELECTRICAL
Circuit Inspection
1. Start the engine.
2. When disconnecting the oil pressure switch con-
nector then connecting the harness side connector
to the ground, check to see if the oil pressure warn-
ing light lights up. When the light will not light up,
check the circuit between the meter and the oil
pressure switch, and repair an open circuit if nec-
essary.
Fuel Tank Unit
The tank unit varies the internal resistance according to
the float position (fluid level) to operate the fuel meter
needle. Also available is the build-in switch type to warn
the driver of low fuel level (about 5 liters left in the tank)
by illuminating the fuel warning light.
N8A5410E
N8A5411E
N8A5412E
CAB AND CHASSIS ELECTRICAL 8-335
Inspection
(Level Switch type of warn low fuel level)
1. Check the resistance between the connector terminals 1
and 3
while shifting the float from “E” to “F”
point.
2. Check if the low fuel warning switch turns on and off at the specified positions. If found defective, replace the
fuel tank unit.
J-28
J-28
N8A5413E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст