Isuzu N-Series. Manual — part 815
7B-30 MANUAL TRANSMISSION (MSB)
17. Spring Pin
• Setting the hole of the shift arm and shift block
to that of the shift rod, fix them with a new
spring pin.
• Install spring pin properly with the slit in line
with the shaft center line.
18. Interlock Ball
• Apply small amount of multi-purpose grease to
the interlock balls.
• Install the 2 interlock balls in position between
the 5th/reverse shift rod and 3rd/4th shift rod.
19. Interlock Pin
20. 3rd/4th Shift Rod
21. 3rd/4th Shift Block
• Apply small amount of multi-purpose grease to
the interlock pin.
• Insert an interlock pin into the 3rd/4th shift rod.
• Turning the detent groove to the outside (de-
tent ball side), insert the shift rod from the front
side with the detent groove side at the front.
22. Spring Pin
• Setting the hole of the shift arm and shift block
to that of the shift rod, fix them with a new
spring pin.
• Install spring pin properly with the slit in line
with the shaft center line.
N7A0117E
N7A0118E
N7A0119E
N7A0120E
MANUAL TRANSMISSION (MSB) 7B-31
23. Interlock Ball
• Apply small amount of multi-purpose grease to
the interlock balls.
• Install the 2 interlock balls in position between
the 3rd/4th shift rod and 1st/2nd shift rod.
24. 1st/2nd Shift Rod
25. 1st/2nd Shift Block
• Before reassembly, set the 5th/reverse and
3rd/4th shift rods already reassembled in neu-
tral position.
• Turning the detent groove to the outside (de-
tent ball side), insert the shift rod from the front
side with the detent groove side at the front.
26. Spring Pin
• Setting the hole of the shift arm and shift block
to that of the shift rod, fix them with a new
spring pin.
• Install spring pin properly with the slit in line
with the shaft center line.
27. Spacer
28. Vehicle Speed Sensor Drive Gear
N7A0121E
N7A0122E
N7A0123E
N7A0124E
7B-32 MANUAL TRANSMISSION (MSB)
29. Rear Cover
• Apply engine oil to the new oil seal outer cir-
cumference and apply multi-purpose grease to
the oil seal lip.
• Use the oil seal installer to install oil seal to the
rear cover.
Oil Seal Installer: 5-8840-2242-0
• Remove water and oil on the mating face be-
fore applying the liquid gasket.
• Apply a
φ2 mm (0.1 in) bead of the liquid gasket
(Three Bond 1215 or equivalent) to the rear
cover surface shown in the illustration.
Caution:
Install the rear cover on the transmission case within 30
minutes after liquid gasket application.
Tighten:
Rear cover bolts to 20 N
⋅m (2.0 kg⋅m / 14 lb⋅ft)
N7A0075E
N7A0125E
N7A0126E
N7A0074E
N7A0073E
MANUAL TRANSMISSION (MSB) 7B-33
30. Clutch Housing
• Apply engine oil to the new oil seal outer cir-
cumference and apply multi-purpose grease to
the oil seal lip.
• Use the oil seal installer to install the oil seal to
the clutch housing.
Oil Seal Installer: 5-8840-2064-0
• Remove water and oil on the mating face be-
fore applying the liquid gasket.
• Apply a
φ2 mm (0.1 in) bead of the liquid gasket
(Three Bond 1215 or equivalent) to the clutch
housing surface shown in the illustration.
Caution:
Install the clutch housing on the transmission case with-
in 30 minutes after liquid gasket application.
Tighten:
Clutch housing to transmission case bolts to 81 N
⋅m (8.3
kg
⋅m / 60 lb⋅ft)
31. Vehicle Speed Sensor Driven Gear Assembly
Tighten:
Driven gear lock plate bolt to 15 N
⋅m (1.5 kg⋅m / 11 lb⋅ft)
• Install the vehicle speed sensor with key rod.
Tighten:
Vehicle speed sensor to 25 N
⋅m (2.5 kg⋅m / 18 lb⋅ft)
32. Parking Brake Assembly
Tighten:
Parking brake bolts M8 to 25 N
⋅m (2.6 kg⋅m / 19 lb⋅ft)
N7A0060E
N7A0061E
N7A0066E
N7A0072E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст