Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Manual — part 149
4D2–10 TRANSFER CASE (TOD)
Disassembly
1. Remove the drain plug from the transfer case and
drain the oil.
2. Remove the speedometer sensor and driven gear.
3. Remove the front and rear speed sensor of the
harness assembly from the transfer cover assembly.
NOTE: Use care to prevent damage to speed sensor
when removing speed sensor.
4. Disconnect the clutch solenoid coil, 4H and 4L switch
harness connector.
D
Remove the harness bracket from the transfer
cover.
261RY00009
5. Remove the connector bracket from the transfer
case.
D
Remove the harness assembly and shift motor
harness connector from the connector bracket.
261RY00010
6. Remove the 4H and 4L switch from the transfer case.
7. Remove the shift motor assembly from the transfer
cover.
8. Using the flange holder J–8614–11, remove the end
nut.
Remove the washers, oil seals, front and rear
companion flange.
262RY00012
9. Remove the transfer cover retaining bolts and the
transfer cover assembly from the transfer case
assembly.
NOTE: When removing the transfer cover assembly, use
care to prevent damage to oil seal.
10. Remove the breather hose from the transfer case.
Reassembly
1. Apply recommended liquid gasket (LOCTITE 598 or
its equivalent) uniformly to the transfer case and
cover fitting surface.
261RY00011
4D2–11
TRANSFER CASE (TOD)
2. Install the plate, bracket, connector bracket and
ground cable of the harness assembly, and tighten
the transfer cover retaining bolts (16 pieces) to
specified torque.
Torque: 31 N·m (23 lb ft)
261RY00035
261RY00037
3. Install the front and rear companion flange.
4. Install the oil seal and washer, and using the flange
holder J–8614–11, install the new end nut to the
specified torque.
Torque: 167 N·m (123 lb ft)
5. Securely stake the end nut at one spot.
NOTE: Be sure to confirm that there is no clack at the
staked portion of the end nut after staking.
266RY00003
266R200004
4D2–12 TRANSFER CASE (TOD)
6. Apply recommended liquid gasket (LOCTITE 598 or
its equivalent) to the transfer cover and shift motor
assembly fitting surface.
261R200003
7. Install the shift motor assembly to the transfer cover
assembly.
Torque: 10 N·m (87 lb in)
8. Install the 4H and 4L switch.
Torque: 24 N·m (17 lb ft)
9. Install the harness assembly and shift motor harness
connector to the connector bracket.
10. Install the front and rear speed sensors to the transfer
cover.
Torque: 5 N·m (43 lb in)
11. Connect the harness assembly connector to the
clutch solenoid coil harness connector and 4H and 4L
switch.
D
Fix the harness with harness bracket.
261RY00009
12. Install the driven gear and speedometer sensor to the
transfer case.
Torque: 25 N·m (19 lb ft)
261RY00034
13. Remove the filler plug and fill the transfer case with
ATF DEXRON
–II or III.
14. Wind the sealing tape around the filler plug thread and
tighten the plug to the specified torque.
Torque: 25 N·m (19 lb ft)
261RY00026
15. Install the breather hose to the transfer case.
4D2–13
TRANSFER CASE (TOD)
Transfer Cover Assembly
261RY00032
Legend
(1) Coil Assembly
(2) Snap Ring
(3) Ball Bearing
(4) Speed Gear and Tone Wheel
(5) Ball Bearing
(6) Transfer Cover (With Oil Seal)
(7) Oil Drain Plug and Oil Filler Plug
Disassembly
1. Using a precision screwdriver or a suitable tool, push
down the lock to unlatch the terminal for the coil
assembly, and pull the terminal out.
NOTE: Use care to prevent damage to harness terminal
and connector.
261RY00013
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст