Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Manual — part 1114
3D–18
REAR SUSPENSION
Special Tools
ILLUSTRATION
TOOL NO.
TOOL NAME
J–39214
Remover and Installer;
Trailing link bushing
J–43008
Remover and Installer;
Upper link bushing
J–39792
Remover and Installer;
Lateral rod bushing (Axle
side)
J–39215
Remover and Installer;
Lateral rod bushing
(Frame side)
WHEEL AND TIRE SYSTEM
3E–1
RODEO
SUSPENSION
CONTENTS
WHEEL AND TIRE SYSTEM
Service Precaution. . . . . . . . . . . . . . . . . . . . .
3E–1
General Description . . . . . . . . . . . . . . . . . .
3E–2
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . .
3E–3
Wheel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3E–11
Wheel and Associated Parts . . . . . . . . . . .
3E–11
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .
3E–11
Installation. . . . . . . . . . . . . . . . . . . . . . . . . .
3E–11
Tire. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3E–12
Tire Replacement . . . . . . . . . . . . . . . . . . . .
3E–12
General Balance Procedure . . . . . . . . . . . .
3E–12
Balancing Wheel and Tire. . . . . . . . . . . . . .
3E–13
Main Data and Specifications . . . . . . . . . . . .
3E–14
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO
THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFER
TO THE
SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or
other corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener.
When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.
3E–2
WHEEL AND TIRE SYSTEM
General Description
480RS008
Replacement wheels or tires must be equivalent to the
original equipment in load capacity, specified dimension
and mounting configuration. Improper size or type may
affect bearing life, brake performance, speedometer/
odometer calibration, vehicle ground clearance and tire
clearance to the body and chassis. All models are
equipped with metric sized tubeless steel belted radial
tires. Correct tire pressures and driving habits have an
important influence on tire life. Heavy cornering,
excessively rapid acceleration and unnecessary sharp
braking increase premature and uneven wear.
WHEEL AND TIRE SYSTEM
3E–3
Diagnosis
Condition
Possible cause
Correction
Vehicle Pulls
Mismatched or uneven tires.
Replace tire.
Tires not adequately inflated.
Adjust tire pressure.
Broken or sagging springs.
Replace spring.
Radial tire lateral force.
Replace tire.
Improper wheel alignment.
Adjust wheel alignment.
Brake dragging in one wheel.
Repair brake.
Loose, bent or broken front or rear
suspension parts.
Tighten or replace the appropriate
suspension part(s).
Faulty shock absorbers.
Replace shock absorber.
Parts in power steering valve
defective.
Replace power steering unit.
Abnormal or Excessive Tire Wear
Sagging or broken spring.
Replace spring.
Tire out of balance.
Balance or replace tire.
Improper wheel alignment.
Check front end alignment.
Faulty shock absorber.
Replace shock absorber.
Hard driving.
Replace tire.
Overloaded vehicle.
Replace tire and reduce load.
Tires not rotated periodically.
Replace or rotate tire.
Worn hub unit bearings.
Replace hub unit bearing.
Wobbly wheel or tires.
Replace wheel or tire.
Tires not adequately inflated.
Adjust the pressure.
Wheel Hop
Blister or bump on tire.
Replace tire.
Improper shock absorber operation.
Replace shock absorber.
Shimmy, Shake or Vibration
Tire or wheel out of balance.
Balance wheels or replace tire/or
wheel.
Loose hub unit bearings.
Replace hub unit bearing.
Worn steering linkage ball joints.
Replace ball joints.
Worn upper or lower end ball joints.
Replace ball joints.
Excessive wheel runout.
Repair or replace wheel and/or tire.
Blister or bump on tire.
Replace tire.
Excessive loaded radial runout of
tire/wheel assembly.
Replace tire or wheel.
Improper wheel alignment.
Check wheel alignment.
Loose or worn steering linkage.
Tighten or replace steering linkage.
Loose steering unit.
Tighten steering unit.
Tires not adequately inflated.
Adjust tire pressure.
Loose, bent or broken front or rear
suspension parts.
Tighten or replace the appropriate
suspension parts.
Faulty shock absorber.
Replace shock absorber.
Parts in power steering valve
defective.
Replace power steering unit.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст