Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Manual — part 221
6A–71
ENGINE MECHANICAL (6VE1 3.5L)
015RS012
Legend
(1) Number 1 and 4 main bearing upper and lower
(2) Number 2 and 3 main bearing upper
(3) Number 2 and 3 main bearing lower
mm ( in)
1 Size
Mark
Main Bearing
Bore Diameter
Crank Shaft Main
Journal Diameter
2 Size
Mark
Crank
Shaft
Bearing
Size Mark
(Upper
Side)
Crank
Shaft
Bearing
Size Mark
(Lower
Side)
Oil Clearance
(Reference)
1
68.994-69.000
63.918-63.925
(2.5165-2.5167)
2
Blue
Blue
0.030-0.049
(0.0012-0.0019)
1
(2.7163-2.7165)
63.926-63.933
(2.5168-2.5170)
1
Brown
Brown
0.028-0.047
(0.0011-0.0019)
2
68.987-68.993
63.918-63.925
(2.5165-2.5167)
2
Brown
Brown
0.029-0.048
(0.0011-0.0019)
2
(2.7160-2.7163)
63.926-63.933
(2.5168-2.5170)
1
Green
Green
0.027-0.046
(0.0011-0.0018)
3
68.980-68.986
63.918-63.925
(2.5165-2.5167)
2
Green
Green
0.028-0.047
(0.0011-0.0019)
3
(2.7157-2.7160)
63.926-63.933
(2.5168-2.5170)
1
Yellow
Yellow
0.026-0.045
(0.0010-0.0018)
Reassembly
1. Crankshaft (12)
D
Install the main bearings to the cylinder block and
the main bearing caps.
D
Be sure that they are positioned correctly.
D
Apply new engine oil to the upper and lower main
bearing faces.
NOTE: Do not apply engine oil to the main bearing back
faces.
015RS012
6A–72
ENGINE MECHANICAL (6VE1 3.5L)
D
Carefully mount the crankshaft.
D
Apply engine oil to the thrust washer.
D
Assemble the thrust washer to the No.3 bearing
journal. The oil grooves must face the crankshaft.
015RS013
2. Rear oil seal (10)
D
Remove the oil from the cylinder block and the
retainer mounting surface.
D
Apply sealant (TB–1207B or equivalent) to the
retainer mounting surface, following the pattern
shown in the illustration.
The retainer must be installed within 5 minutes after
sealant application to prevent premature hardening
of sealant.
015RW002
Legend
(1) Around Bolt Holes
(2) Around Dowel Pin
D
Apply engine oil to the oil seal lip.
D
Align the cylinder block dowel pin holes with the rear
retainer dowel pins.
D
Tighten the rear retainer fixing bolts. New bolts
should be used when installing rear retainer.
Torque: 18 N·m (13 lb ft)
NOTE: Be very careful not to disengage the oil seal garter
spring during installation of the rear retainer.
If the seal was removed from retainer for
replacement, apply engine oil to the oil seal lip and
install the oil seal using J–39201 oil seal installer.
015RW001
015RS017
3. Flywheel (9)
1. Thoroughly clean and remove the oil from the
threads of crankshaft.
2. Remove the oil from the crankshaft and flywheel
mounting faces.
3. Mount the flywheel on the crankshaft and then
install the washer.
6A–73
ENGINE MECHANICAL (6VE1 3.5L)
4. Hold the crankshaft to prevent from rotating then
install the bolts in the order shown to the specified
torque.
Torque: 54 N·m (40 lb ft)
NOTE: Do not reuse the bolt and do not apply oil or thread
lock to the bolt.
015RS018
4. Piston and connecting rod assembly (8)
D
Apply engine oil to the cylinder bores, the
connecting rod bearings and the crankshaft pins.
Check to see that the piston ring end gaps are
correctly positioned.
015RS019
Legend
(1) No.1 Compression Ring
(2) No.2 Compression Ring
(3) Oil Ring Side Rail Upper
(4) Oil Ring Side Rail Lower
(5) Piston Front Mark
D
Insert the piston/connecting rod assemblies into
each cylinder with the piston ring compressor. The
front marks must be facing the front of the engine.
D
Match the numbered caps with the numbers on the
connecting rods. Align the punched marks on the
connecting rods and caps.
D
Apply engine oil to the threads and seating faces of
the nuts.
D
Tighten the nuts.
Torque: 54 N·m (40 lb ft)
After tightening the cap nuts, check to see that the
crankshaft rotates smoothly.
NOTE: Do not apply engine oil to the bearing back faces.
015RS020
5. Install oil gallery (7) and tighten the bolts in 2 steps, in
the order shown.
1st step: 29 N·m (22 lb ft)
2nd step: 55
°
∼
65
°
051RS009
6A–74
ENGINE MECHANICAL (6VE1 3.5L)
6. Cylinder block side bolts (6)
D
Tighten all the bolts to the specified torque in the
order shown.
NOTE: Do not apply engine oil to the crank case side
bolts.
Torque: 39 N·m (29 lb ft)
012RS001
7. Install oil pump assembly (5), refer to “Oil pump” in
this manual.
8. Install oil strainer and O-ring (4).
9. Install oil pipe and O-ring (3) and tighten the bolts.
Torque: 25 N·m (18 lb ft)
10. Install crankcase with oil pan (2).
1. Completely remove all residual sealant, lubricant
and moisture from the sealing surfaces. The
surfaces must be perfectly dry.
2. Apply a correct width bead of sealant (TB—
1207C or its equivalent) to the contact surfaces of
the oil pan. There must be no gaps in the bead.
3. The crankcase assembly must be installed within
5 minutes after sealant application.
4. Tighten the bolts and nuts to the specified torque.
Torque : 10 N·m (87 lb in)
013RW010
Legend
(1) Portion Between Bolt Holes
(2) Bolt Hole Portion
11. Install cylinder head assembly, refer to “Cylinder
head” in this manual.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст