Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Manual — part 500
EXTERIOR/INTERIOR TRIM
8J–19
Roof Moulding
Parts Location
660R200003
Legend
(1) Roof Moulding Assembly
(2) Clips
(3) Roof Panel
(4) Body Side Outer Panel
Removal
1. Remove the roof moulding.
D
Pry the roof moulding covers with the nine clip
positions from the roof panel.
Installation
To install, follow the removal steps in the reverse order.
8J–20
EXTERIOR/INTERIOR TRIM
Power Door Mirror System
General Description
The system consists of the starter switch, door mirror
switch, rear defogger/mirror defogger switch and door
mirrors on both sides.
When the door mirror switch is operated with the starter
switch at either “ACC” or “ON” position, the motor in the
door mirror (on either side) rotates to allow the horizontal
and vertical adjustment of mirror angles.
When the rear defogger/mirror defogger switch is turned
“ON” with the starter switch “ON”, the heater of the left
and right mirrors and the tailgate glass are activated.
Door Mirror Switch
Removal
1. Disconnect the battery ground cable.
2. Remove the instrument panel lower cover (2).
Refer to the
Instrument Panel Assembly in Body
Structure section.
3. Remove the door mirror switch (1).
825RW094
Rear Defogger/Mirror Defogger Switch
Refer to the
Rear Defogger/Mirror switch removal and
installation steps in Lighting System section.
Door Mirrors
Refer to
Door Mirror Assembly in this section.
EXTERIOR/INTERIOR TRIM
8J–21
Power Window System
General Description
The power window system consists of power window
switches and power window motors on driver and
passenger sides and power window relay. With the starter
switch in “ON” position, the battery voltage is supplied
through power window relay to the power window
switches on driver and passenger sides. Selection of up
or down switch changes the motor rotating direction to
open or close the window.
When the power window “LOCK” switch on the driver side
is pressed, the power source for the other switches are
disconnected causing the power window operation to
seize.
Power Window Switch Driver Seat
Side
Removal
1. Disconnect the battery ground cable.
2. Remove the switch (1).
D
Pull out the switch by pushing the spring with the tip
of a screwdriver.
D
Disconnect the connector.
635R200002
Installation
To install, follow the removal steps in the reverse order.
Front Passenger Seat Side
Removal
1. Disconnect the battery ground cable.
2. Remove the switch (1).
D
Pull out the switch by pushing the spring (2) with the
tip of a screwdriver.
D
Disconnect the connector.
825R200025
Installation
To install, follow the removal steps in the reverse order.
Rear-Left and Right Sides
Removal
1. Disconnect the battery ground cable.
2. Remove the rear power window switch (1).
D
Pull out the switch by pushing the spring with the tip
of a screwdriver.
D
Disconnect the connector.
655R200004
Installation
To install, follow the removal steps in the reverse order.
8J–22
EXTERIOR/INTERIOR TRIM
Power Window Motor
Driver Seat Side
Removal
1. Disconnect the battery ground cable.
2. Remove the window regulator assembly (2).
D
Refer to the
Window Regulator and Glass removal
steps in Body Structure section.
3. Remove the power window motor (1).
D
Remove three screws.
635R200007
Installation
To install, follow the removal steps in the reverse order.
Front Passenger Seat Side
Removal and Installation
Refer to the
Front Window Motor — Driver Seat side
removal and installation steps in this section.
Rear-Right Side
Removal
1. Disconnect the battery ground cable.
2. Remove the rear window regulator assembly (2).
D
Refer to the
Rear Window Regulator and Glass
removal steps in Body Structure section.
3. Remove the power window motor (1).
D
Remove three screws.
655R200006
Installation
To install, follow the removal steps in the reverse order.
Rear-Left Side
Removal and Installation
Refer to the
Rear Power Window Motor — Right Side
removal and installation steps in this section.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст