Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Manual — part 1152
4C–20
DRIVE SHAFT SYSTEM
Actuator
Check and see that there is no damage, cracking, or
other abnormality.
Functional Check
412RY00041
412RY00009
Wake sure of function with boltage (12V) applied to
terminal 3, 4 and set the tester to terminal 1, 2 in
accordance with the table below.
If there is an abnormality, replace the actuator as an
assembly.
NOTE: Be careful not to permit the entry of water or
dust into of the actuator.
Dimentional Check
Measure illustrated sizes 1, 2, and 3.
412RY00010
Limit
1=64.3mm (2.53in)
2=6.7mm (0.26in)
3=6.7mm (0.26in)
Reassembly
1. Install the new oil seal which has been immersed in
differential gear oil, by using an oil seal installer J–
41693 and grip J–8092.
412RW034
State
Trminal 3
Trminal 4
Electric
circuit
between
terminal 1 &
2
Functio
n
A
+12V
Ground
OK
2WD
B
Ground
+12V
NONE
4WD
DRIVE SHAFT SYSTEM
4C–21
2. Force a new needle bearing into inner shaft by
using a Installer J–41694 and grip J–8092.
412RS051
3. Place a new snap ring(internal) in inner shaft.
Force a new inner shaft bearing into the inner shaft.
412RS044
4. Install snap ring(external).
NOTE: Be careful not to damage the inner shaft.
5. Clean the housing contact surface of the front axle
case and insert inner shaft assembly into the front
axle case.
NOTE: Be careful not to damage seal.
6. Install snap ring internal in the groove of front axle
case.
NOTE: Be sure to install the snap ring properly.
412RW017
7. Apply differential gear oil to clutch gear, then install
clutch gear.
8. Apply differential gear oil to sleeve, then install
sleeve.
9. Clean contact surface with the front axle and
actuator mounting surface. Apply liquid gasket to
the contact surface on the front axle case, then
install in the housing.
412RW023
10. Tighten bolts to specified torque.
Torque: 75N·m(55lb ft)
11. Clean the actuator contact surface with the housing
then Install and tighten shift position switch to the
specified torque.
Torque: 39N·m (29 lbft)
4C–22
DRIVE SHAFT SYSTEM
12. Apply liquid gasket to the contact surface on the
actuator side.
412RW012
13. Align shift arm with the groove of sleeve and install
the actuator.
14. Tighten bolts to specified torque.
Torque:9N·m(78lb in)
15. Install front axle drive shaft and mounting bracket.
Tighten fitting bolts to specified torque.
Torque:116N·m (85 lb ft)
16. Pour specified amount of differential gear oil to filler
plug.
Front Differential
Oil Capacity:1.25lit (1.32US qt)
A ctuator Housing
Oil Capacity:0.12lit(0.13US qt)
17. Install filler plug through gasket and tighten to
specified torque.
Torque:78N·m (58lb ft)
DRIVE SHAFT SYSTEM
4C–23
Main Data and Specifications
General Specifications
Torque Specifications
412RY00040
Front drive axle oil capacity
1.25 liter (1.32 US qt)(Differential)
0.12 liter (0.13 US qt)(Actuator Housing:Shift on the fly)
Type of lubricant
GL–5 (75W–90) Refer to chart in General Information
Axle shaft type
Constant velocity joint(Birfield joint type and double offset joint)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст