Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Manual — part 641
DRIVE LINE CONTROL SYSTEM (TOD)
4B2–84
Step
Action
Yes
No
1
1. Disconnect ECU terminal.
2. Turn on the starter switch.
Is battery voltage observed between ECU terminals (B–48)18
and (B–48)24?
Go to Step 2
Wires are broken
lighting SW
circuit. Repair
the circuit.
Go to Step 4
2
Turn lighting SW “ON”.
Is 0 V observed between ECU terminal (B–48)18 and (B–48)24?
Go to Step 3
Lighting SW
circuit battery
short. Repair the
circuit.
Go to Step 4
3
Connect ECU terminal.
While the lighting switch is pressed on and off, does the
brightness of the indicator change?
The phenomenon
is not
reproduced.
Refer to
“Troubles
intermittently
observed”
The ECU has
failed. Replace
the ECU.
Go to Step 4
4
Check that all the parts are mounted.
Is this step complete?
Repeat the
“Diagnosis Flow”.
Return to Step 4
4B2–85
DRIVE LINE CONTROL SYSTEM (TOD)
Diagnosis from Symptom
Troubles that are not indicated by the warning lamp are
listed in the table below. These troubles are caused by
the faults that cannot be detected by the self-diagnostic
function of the control unit.
If this type of trouble is observed, interview the customer
and conduct test runs to reproduce the trouble,
cross-check the reported trouble with the listed
phenomena, and diagnose and analyze the trouble on the
item by item basis.
Phenomena
Major cause
Corrective action
1
The tight corner braking is ob-
served when the vehicle is subject
to full steering.
D
The standard tires are not used.
D
The tire pressure is incorrect.
D
The tires are worn inuniformity.
D
The transfer or wiring is
imperfect.
D
The limited slip differential is
failed.
Check and recondition the ve-
hicle according to Chart 1.
2
Even if the 4WD Auto Switch is se-
lect to the 4WD position, the 4WD
mode is not active, resulting in re-
markable rear wheel spin.
D
The transfer or wiring is
imperfect.
D
The shift on the fly system is
failed.
Check and recondition the ve-
hicle according to Chart 2.
3
D
When the 4WD Auto Switch is
select to the 4WD position, the
drive resistance of the 4WD
system is too large to get
sufficient running speed.
D
Noised drive line.
D
The standard tires are not used.
D
The tire pressure is incorrect.
D
The tires are worn inuniformity.
D
The transfer or wiring is
imperfect.
D
The limited slip differential is
failed.
Check and recondition the ve-
hicle according to Chart 1.
4
The shift on the fly system (front
axle) generates gear noises.
D
The wiring is imperfect.
D
The shift on the fly system is
failed.
Check and recondition the ve-
hicle according to Chart 3.
5
The braking distance gets long
even when the ABS is active.
D
The wiring is imperfect.
D
The ABS is failed.
Check and recondition the ve-
hicle according to Chart 4.
DRIVE LINE CONTROL SYSTEM (TOD)
4B2–86
Chart 1
The tight corner braking is observed.
Function of circuit
—
Fail condition
When the vehicle is subject to full steering in the TOD mode, the drive resistance gets
large or the judder occurs. Otherwise, the above phenomenon is observed only when the
brake is applied.
D04RY00009
4B2–87
DRIVE LINE CONTROL SYSTEM (TOD)
Step
Action
Yes
No
1
Are the front and rear tires in specified size?
Go to Step 2
Replace the tires
with specified
ones, and service
the new tires.
Go to Step 16
2
Is the tire pressure correct?
Go to Step 3
Inflate the tires to
recommended
pressure.
Go to Step 16
3
Are the tires free from abnormal wear?
Go to Step 4
Replace the tires
with specified
ones, and service
the new tires.
Go to Step 16
4
Are different types of tires used?
Go to Step 5
Replace the tires
with specified
ones, and service
the new tires.
Go to Step 16
5
1. Start the engine.
2. Shift the transfer lever to the high (TOD) position and switch
the 4WD AUTO switch to the 4WD position.
3. Fully turn the steering to the left (or right) end, and select the D
range and start the creep run.
Does the tight corner braking occur? Is the judder with chug-chug
sound observed? * Use caution on the operation.
Go to Step 6
Go to Step 11
6
1. Shift the transfer lever to the high position and switch the 4WD
AUTO switch to the 2H position.
2. Fully turn the steering to the left (or right) end, and select the D
range and start the creep run.
Does the tight corner braking occur? Is the judder with chug-chug
sound observed? * Use caution on the operation.
Go to Step 7
Go to Step 14
7
Is an LSD mounted to the rear differential?
Go to Step 8
Go to Step 9
8
Is the genuine LSD oil used in the rear differential?
Go to Step 9
Replace the
differential oil.
Go to Step 16
9
Does the engine output the power correctly?
Go to Step 10
Check the
engine.
Go to Step 16
10
Do the speed sensors work correctly? (Check trouble codes.)
The ECU has
failed. Replace
the ECU.
Go to Step 16
Replace the
speed sensors.
Go to Step 16
11
Is the tight corner braking observed only when the brake is
applied?
Go to Step 12
Conduct full
steering under
WOT.
Go to Step 5
12
Turn on the starter switch.
Is the battery voltage observed between terminals 33 and 46?
Go to Step 13
Repair the circuit
of terminal 33
(ABS IN).
Go to Step 16
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст