Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Manual — part 452
WIPER/WASHER SYSTEM
8B–7
Windshield Wiper Blade Rubber
Removal
1. Push the wiper blade lock(1) while pulling the wiper
blade in the arrow direction as shown in the figure.
CAUTION: When the wiper blade has been
removed, wrap the tip of the wiper arm with cloth, to
avoid damaging the glass.
880RS011
2. Pull the end of rubber and remove the concavity (3)
from the click of the blade stay (2).
880R200002
3. Pull the rubber out in the same direction.
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. Install the click of the blade stay in the groove of the
new rubber and slide it in. Complete wiper blade
installation by pushing the click in the concavity (3).
880R200003
2. Finally, check that the click of the stay has caught in
the hole of the rubber.
880R200004
8B–8
WIPER/WASHER SYSTEM
Rear Wiper/Washer System
General Description
The circuit consists of the starter switch, rear wiper &
washer switch, rear wiper motor, rear washer motor and
Alarm & relay control unit.
When the rear wiper & washer switch is turned on with the
starter switch on, the battery voltage is applied to the
wiper motor to activate the wiper.
The washer motor squirts glass cleaning fluid while the
washer switch is being pushed. The alarm & relay control
unit is used to control motion of the wiper.
Rear Wiper and Washer Switch
Removal
1. Disconnect the battery ground cable.
2. Remove the dash side trim panel(1).
3. Remove the lower cover assembly(2).
821RW254–1
4. Remove the rear wiper & washer switch (4).
D
Disconnect the connector.
D
Push the lock from the back side of the lower cover
assembly (3).
825R200028
Installation
To install, follow the removal steps in the reverse order,
noting the following point:
1. Push the switch with your fingers until it locks
securely.
WIPER/WASHER SYSTEM
8B–9
Rear Wiper Motor
Removal
1. Disconnect the battery ground cable.
2. Remove the tailgate trim pad.
D
Refer to
Tailgate Trim Pad in Body Structure
section.
3. Remove the wiper arm/blade.
Refer to
Rear Wiper Arm/Blade in this section.
4. Remove the rear wiper motor (1).
D
Disconnect the connector.
D
Remove the rear wiper motor fixing screws.
885R200002
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. Before installing the wiper arm/blade (1) to the motor
shaft (6), confirm that the motor stops at the autostop
position.
2. Tighten the motor shaft nut (5) to the specified torque.
Torque: 10 N·m (87 lb in)
3. Tighten the wiper arm nut (3) to the specified torque.
Torque: 9 N·m (78 lb in)
885R200001
4. Install the wiper arm/blade so that the wiper arm
contact as shown in the figure.
885R200005
8B–10 WIPER/WASHER SYSTEM
Rear Washer Motor
Removal
1. Disconnect the battery ground cable.
2. Remove the fender panel (right side).
D
Refer to
Fender Panel in Body Structure section.
3. Disconnect the windshield washer motor connector
and the rear washer motor connector.
4. Disconnect the windshield washer hose connector
and the rear washer hose connector.
5. Remove the filler neck (3).
D
Remove the bolt.
6. Remove the washer tank (2).
D
Remove the three nuts.
7. Remove the rear washer motor (1).
D
Pull out the motor from the washer tank.
880R200001
Installation
To install, follow the removal steps in the reverse order.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст