Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Manual — part 1149
4C–8
DRIVE SHAFT SYSTEM
Reassembly
1. Install the wheel pin.
• Place hub on a wood workbench or a block of
wood approx. 6" by 6" to protect the wheel stud
ends and thresds.
• Install wheel stud, using a hammer.
NOTE: Be sure wheel stud is started squarely and
seats completely.
411RS005
2. Install the ABS rotor sensor to the hub unit bearing.
Tighten the bolts to the specified torque.
A BS rotor sensor bolt
Torque: 18.7
±5 N·m (1.9±0.8 kg·m)
3. Install the hub unit bearing to the knuckle. Tighten
the bolts to the specified torque.
Hub unit bearing bolt
Torque: 103
±10 N·m (10.5±1 kg·m)
If there is rust on the bearing and knuckle contact
surfaces, use sandpaper to remove it before installation.
Take care not to push the front drive shaft and oil seal
out of position.
4. Hand tighten the front drive shaft nuts.
Use new nuts.
5. Install the disc rotor.
6. Install the brake caliper to the bracket.
Refer to Front disc caliper assembly in Section 5C of
this Manual.
7. Tighten the front drive shaft nuts to the specified
torque.
Front drive shaft nut
Torque: 245
±19.6 N·m (25±2 kg·m)
411R200005
8. Caulk the front drive shaft nuts.
The caulking must be free of cracks.
411R200006
DRIVE SHAFT SYSTEM
4C–9
Front Drive Shaft Joint
Front Drive Shaft Joints
Replacement
• Refer to Front Drive Axle Assembly Replacement in
this section, and refer to Front Hub and Disc
Overhaul in Suspension section.
Front Hub Bearing Preload Check
Check the hub bearing preload at the wheel pin.
New bearing and New oil seal:
24.5 N (4.4 – 5.5 lb)
Used bearing and New oil seal:
11.8– 17.7 N(2.6 – 4.0lb)
Inspection Of Shift On The Fly System Gear
Oil
412RY00008
1. Open filler plug and make sure that the oil is up to
the plug port.
If the oil is short, replenish with gear oil GL–5 grade.
2. Tighten the filler plug to specified torque.
Torque:78 N·m (58lb in)
4C–10
DRIVE SHAFT SYSTEM
Front Axle Drive Shaft
Front Axle Drive Shaft and Associated Parts
412R200009
EndOFCallout
Legend
(1) Axle Case and Differential
(2) Snap Ring
(3) Bearing
(4) Snap Ring
(5) Oil Seal
(6) Bracket
(7) DOJ Case
(8) Circlip
(9) Bolt
(10) Drive Shaft Joint Assembly
(11) Ball
(12) Snap Ring
(13) Ball Retainer
(14) Ball Guide
(15) Band
(16) Bellows
(17) Band
(18) Band
(19) Bellows
(20) Band
(21) BJ Shaft
(22) Dust Seal
DRIVE SHAFT SYSTEM
4C–11
Disassembly
NOTE: For the left side, follow the same steps as right
side.
1. Raise the hooked end of the band with a
screwdriver or equivalent.
412RS009
2. Remove band(1).
3. Pry off circlip (1) with a screwdriver or equivalent.
412RS010
4. Remove drive shaft joint assembly.
5. Remove the six balls (1) with a screwdriver or
equivalent.
412RS012
6. Using snap ring pliers, remove the snap ring (1)
fastening the ball retainer to the center shaft.
412RS013
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст