Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Manual — part 1163
TRANSFER CASE
4D–21
Inspection and Repair
Refer to
Transfer Case Assembly in this section for
inspection and repair.
Reassembly
1. Place shift block (15) in transfer case (16).
2. Set shift arm (14) on the High–Low sleeve.
3. Push High–Low shift rod (13) through shift arm (14)
and block (14).
4. Engage the High–Low sleeve with the 4H (1) side.
5. Install the spring pin (12) to the shift block (15) and
shift arm (14).
262RW034
6. Install select rod assembly (11), joining its lever to
shift block groove.
7. Engage the High–Low sleeve with the 4H side and
install the interlock pin and spring (10) in the proper
direction.
8. Place 2WD–4WD shift block in the transfer case
(16).
9. Set 2WD–4WD shift arm on the 2WD–4WD sleeve.
10. Puh 2WD–4WD shift rod through 2WD–4WD shift
arm and 2WD–4WD shift block.
11. Install the shift rod: 2WD–4WD (5) with interlock pin
pushed in.
262RW035
EndOFCallout
12. Install 4WD indicator switch and gasket (8).
Tighten to the specified torque.
Torque: 39 N·m (29 lb ft)
13. Install spring (4).
Legend
(18) 2WD–4WD
(19) 4H Side
(20) Interlock pin
(21) 2WD
(22) 4WD
(23) Rod: 2–4
(24) Rod: H–L
(25) 4H
(26) 4L
(27) 4
´2
(28) 4
´4
4D–22
TRANSFER CASE
14. Engage the 2WD–4WD sleeve with the 4WD side
and install the spring pin (3).
262RW022
15. Install spring pin (2) and bridge (2).
16. Install detent ball, spring, gasket and plug and
tighten the plug to the specified torque.
Torque: 25 N·m (18 lb ft)
TRANSFER CASE
4D–23
Transfer Case Assembly
Disassembled View
226RW209
Legend
(1) Bearing Snap Ring
(2) Ball Bearing
(3) Lock Nut
(4) Snap Ring (A/T)
(5) Input Shaft Assembly (A/T)
(6) High–Low Clutch Hub and Sleeve
(7) Transfer Input Gear
(8) Needle Bearing
(9) Bearing Collar
(10) Ball
(11) Plate
(12) Ball Bearing (A/T)
(13) Input Shaft (A/T)
(14) Bearing Snap Ring
(15) Front Output Gear Assembly
(16) Bearing Snap Ring
(17) Ball Bearing
(18) Bearing Collar
(19) Sub–Gear Snap Ring (M/T)
(20) Spacer (M/T)
(21) Belleville Spring (M/T)
(22) Sub–Gear (anti–lash plate) (M/T)
(23) Front Output Gear
(24) Needle Bearing
(25) Inside Ring
(26) Outside Ring
(27) Block Ring
(28) 2WD–4WD Clutch Hub and Sleeve Assembly
(29) Stopper Plate
(30) Ball Bearing
(31) Front Output Shaft
4D–24
TRANSFER CASE
EndOFCallout
Disassembly
1. Use a pair of snap ring pliers to remove the snap
ring (1).
2. Use a bearing remover J–37217 and puller J–37487
to remove the ball bearing (2).
262RW016
3. Install the front companion flange temporarily.
4. Use the Companion flange holder J–8614–11 and
lock nut wrench J–37219 to remove the lock nut (3).
226RX001
5. Remove the front companion flange.
6. Remove snap ring (4). (A/T)
7. Remove the input shaft assembly (5) from the
transfer case (42). (A/T)
265RW001
8. Use the universal puller to remove the high–low
clutch hub and sleeve (6), and transfer input gear
(7).
226RS070
(32) Bearing Snap Ring
(33) Counter Gear Assembly
(34) Snap Ring
(35) Ball Bearing
(36) Snap Ring
(37) Ball Bearing
(38) Spacer
(39) Belleville Spring
(40) Sub–Gear (anti–lash plate)
(41) Counter Gear
(42) Transfer Case (with oil seal)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст