Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Manual — part 53
3C–8
FRONT SUSPENSION
3. Apply the setting marks(2) to the height control arm
and torsion bar, then remove height control arm.
410RS005
4. Apply the setting marks(3) to the torsion bar and
lower control arm, then remove torsion bar.
410RS006
Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal condition are
found through inspection.
Check the following parts:
D
Torsion bar
D
Height control arm
D
Adjust bolt
D
Rubber seat
Installation
1. Apply grease to the serrated portions, then install
torsion bar. Make sure the bars are on their correct
respective sides and align the setting marks(3).
410RS007
410RS006
FRONT SUSPENSION
3C–9
2. Apply grease to the portion that fits into the bracket
then install height control arm and align the setting
marks(2).
410RS005
3. Apply grease to the bolt portion of the end piece(4).
Apply grease to the portion of the seat(5) that fits into
the bracket.
410RS008
4. Apply grease to the serrated portions.
5. Install adjust bolt and seat, then turn the adjust bolt to
the setting mark(1) applied during disassembly.
NOTE: Adjust the trim height. Refer to
Front End
Alignment Inspection and Adjustment in Steering section.
410RS004
3C–10
FRONT SUSPENSION
Knuckle
Knuckle and Associated Parts
410RW006
Legend
(1) Torsion Bar
(2) Lower Ball Joint, Nut and Cotter Pin
(3) Back Plate
(4) Knuckle Assembly
(5) Knuckle
(6) Needle Bearing (4WD MODEL)
(7) Thrust Washer (4WD MODEL)
(8) Oil Seal (4WD MODEL)
(9) Upper Ball Joint, Nut and Cotter Pin
(10) Wheel Speed Sensor
Removal
1. Raise the vehicle and support the frame with suitable
safety stands.
2. Remove wheel and tire assembly. Refer to
Wheel in
this section.
3. Remove the brake caliper. Refer to
Disc Brakes in
Brake section.
4. Remove the hub assembly. Refer to
Front Hub and
Disk in this section.
5. Remove tie–rod end from the knuckle. Refer to
Power
Steering Unit in Steering section.
6. Remove the speed sensor from the knuckle.
7. Loosen torsion bar by height control arm adjust bolt,
then remove torsion bar. Refer to
Torsion Bar in this
section.
8. Remove wheel speed sensor.
FRONT SUSPENSION
3C–11
9. Remove back plate.
10. Remove lower ball joint by using remover J–29107.
CAUTION: Be careful not to damage the ball joint
boot.
901RW163
11. Remove upper ball joint by using remover J–36831.
CAUTION: Be careful not to damage the ball joint
boot.
901RW162
12. Remove knuckle assembly.
13. Remove oil seal (Except 2WD model).
14. Remove washer (Except 2WD model).
15. Remove needle bearing by using remover J–23907
(Except 2WD model).
901RW044
Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal condition are
found through inspection.
Check the following parts:
D
Knuckle
D
Knuckle arm
D
Needle bearing
D
Thrust washer
Installation
1. Apply appropriate amount of multipurpose type
grease to the new bearing (Approx. 5 g) and install
needle bearing by using installer J–36838 and
J–8092 (Except 2WD model).
901RW045
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст