Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Manual — part 1672
SUN ROOF/CONVERTIBLE TOP
8I–13
Removal
1. Remove the quarter window assembly (LH & RH).
• Peel off the velcro fasteners and unzip the
zippers.
2. Remove the back window assembly (2).
• Peel off the velcro fasteners (3), unzip the zipper
(1) and pull the back window assembly toward
the rear together with the support bar assembly
(4). Then slide the back window out to the side.
NOTE: After removing the side windows and back
window, be careful not to bend or place other objects on
top of them as this could scratch or crack them.
Exercise caution when handling and storing the
windows.
682RY00007
3. Press the lock botton (2) of the soft top latch
assembly (1) and lower the lock knob to disengage
the lock. Then remove the hooks of the tarpaulin
frame assembly (LH & RH).
688RW005
4. Remove the tarpautin assembly.
• Disengage the 14 hocks.
5. Remove the tarpautin frame assembly.
• Remove the four fixing bolts.
Installation
To install, follow the removal steps in the reverse order,
noting the following point.
1. After securely covering the zippers (3) with the flaps
(1), smooth out the fastener tape (2) with your
hands so that there are no folds or turned up
portions of the flaps.
682RW014
8I–14
SUN ROOF/CONVERTIBLE TOP
Resin Top Assembly
Resin Top Assembly and Associated Parts
688RW006
EndOFCallout
Removal
1. Disconnect the battery ground cable.
2. Remove the rear sun roof glass.
• Refer to Sun Roof Glass in this section.
3. Remove the sun roof deflector.
• Remove the four fixing screws.
4. Remove the rear roof bracket covers (4) and
remove both sets of two bolts (3) on the resin top
sides of the rear roof brackets (2).
666RW010
Legend
(1) Rear Sun Roof Assembly
(2) Resin Top Assembly
(3) High Mount Stoplight
(4) Air Outlet Grille Assembly
(5) Rear Quarter Glass
SUN ROOF/CONVERTIBLE TOP
8I–15
5. Remove the air outlet grille assembly (LH & RH).
• Remove the two screws and pull the grille
assemblies off toward the rear.
6. Remove the luggage light assembly and disconnect
the connector.
7. Remove the high mount stoplight assembly and
disconnect the connector.
8. Disconnect the rear washer hose (Right side, inside
air outlet grille assembly).
688RW007
9. Disconnect the harness connector for the resin top
(Left side, behind the luggage side trim).
• Remove the canopy cover (1), the luggage side
lid (2) and luggage side upper cover (3). Then
pull out the harness and disconnect the
connector.
686RX001
10. Remove the resin top assembly.
• Remove the two fixing bolts and nut from the left
and right sides. Lift the resin top and remove.
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Removing and mounting the resin top should
always be performed by two persons.
2. Tighten the resin top fixing bolts and nuts to the
specified torque.
Torque: 15 N·m (11 Ib ft)
8I–16
SUN ROOF/CONVERTIBLE TOP
Seat Belt Cross Bar Assembly
Seat Belt Cross Bar Assembly and Associated Parts
688RY00001
EndOFCallout
Removal
1. Disconnect the battery ground cable.
2. Remove the soft top assembly or resin top
Assembly.
• Refer to Soft Top assembly or Resin Top
Assembly in this section.
3. Remove the luggage side lid (2).
4. Remove the luggage side upper cover (3).
5. Remove the luggage side front cover (4).
6. Remove the canopy cover (1) (Resin top model).
• Remove the two fixing clips.
686RX001
Legend
(1) Seat Belt Cross Bar Assembly
(2) Rear Seat Belt Assembly
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст