Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Manual — part 191
5C–81
POWER–ASSISTED BRAKE SYSTEM
Master Cylinder Assembly
Master Cylinder Assembly and Associated Parts
330R200006
Legend
(1) Electrical Connector
(2) Master Cylinder
(3) 2 attaching Nuts
(4) P&B Valve and Bracket
(5) Brake Pipes
Removal
CAUTION: When removing the master cylinder from
the vacuum booster, be sure to get rid of the internal
negative pressure of the vacuum booster (by,
disconnecting the vacuum hose) in advance.
If any negative pressure remains in the vacuum
booster, the piston may possibly come out when the
master cylinder is being removed, letting the brake
fluid run out.
While removing the master cylinder, do not hold the
piston as it can be easily pulled out.
Outside surface of the piston is the surface on which
seals are to slide. Care should be taken to keep the
surface free of cuts and dents.
1. Disconnect electrical connector.
2. Remove brake pipes and after disconnecting the
brake pipe, cap or tape the openings of the brake pipe
to prevent the entry of foreign matter.
3. Remove 2 attaching nuts.
4. Remove P&B valve and bracket.
5. Remove master cylinder.
Inspection
Excessive brake pedal travel, malfunction or dragging
brake suggests that the master cylinder is defective. In
such cases perform the following visual check:
Visual Check
Make parts replacement as required if wear, distortion,
nicks, cuts, corrosion, or other abnormal conditions are
found through the following parts inspection:
D
Master cylinder body
D
Fluid reservoir
D
O–ring
5C–82 POWER–ASSISTED BRAKE SYSTEM
Master Cylinder Assembly
Master Cylinder Assembly Desassembled View
330R200005
Legend
(1) Spring Pin
(2) Reserve Tank and Reserve Tank Cap
(3) O–ring
(4) Primary Piston Assembly
(5) Secondary Piston Assembly
(6) Cylinder Body
Desassembly
1. Remove the spring pin.
2. Remove the reserve tank and the reserve tank cap.
The brake fulid level switch is built–in to the reserve tank
and cannot be removed.
3. Remove the O–ring.
4. Remove the snap ring.
5. Remove the primary piston assembly.
6. Invert the cylinder body and push on the secondary
piston until the pin falls free.
7. Remove the secondary piston assembly.
8. Remove the cylinder body.
Inspection
Excessive brake pedal travel, malfunction or dragging
brake suggests that the master cylinder is defective. In
such cases perform the following visual check:
5C–83
POWER–ASSISTED BRAKE SYSTEM
Visual Check
Make parts replacement as required if wear, distortion,
nicks, cuts, corrosion, or other abnormal conditions are
found through the following parts inspection:
D
Master cylinder body
D
Fluid reservoir
D
O–ring
D
Wash each part in brake fluid before beginning the
inspection procedure.
D
Check the inside surfaces of the master cylinder for
abrasion, corrosion, and other damage. Replace the
cylinder if necessary.
D
Check the return port for clogging. Clean the port with
a wire and compressed air if nesessay.
D
Check the piston and piston cup for abrasion,
damage, and wear. Replace the piston assembly if
any of these conditions exist.
D
Check the return spring. Replace the spring if it is
weak.
D
Check the snap ring. Replace the snap ring if it is
stretched or weak.
Reassembly
1. Wash each master cylinder internal part in brake fluid
before beginning installation.
2. Install the cylinder body.
3. Press the secondary piston assembly into the
cylinder body and hold it. Thread the pin through the
long hole of the piston to secure the piston assembly.
4. Install the primary piston assembly.
5. Install the snap ring.
6. Install the O–ring
7. Install the reserve tank and the reserve tank cap.
8. Install the spring pin.
Installation
1. Install master cylinder.
When replacing the master cylinder or vacuum
booster or both, always measure the vacuum booster
push rod protrusion and adjust it as necessary (Refer
to
Vacuum Booster in section).
2. Install P&B valve and bracket.
3. Install 2 attaching nuts and tighten the attaching nuts
to the specified torque.
Torque: 13 N·m (113 lb in)
4. Install brake pipes and tighten the brake pipe to the
specified torque.
Master cylinder and P&B valve sides
Torque: 12 N·m (104 lb in)
Others
Torque: 16 N·m (12 lb in)
5. Connect electrical connector.
5C–84 POWER–ASSISTED BRAKE SYSTEM
Main Data and Specifications
General Specifications
Type
Dual–circuit
Piston bore diame-
ter
25.4 mm (1.000 in)
Torque Specifications
E05R200005
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст