Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Manual — part 1210
6A–37
ENGINE MECHANICAL (Y22SE 2.2L)
5. Tighten ten camshaft bracket bolts to the specified
torque by sequence in the illustration.
Torque: 8 N·m (69 lb in)
015RW014
NOTE: Camshaft bearing brackets can be identified by
number 1 through 10.
Camshaft can be identified by stamping.
M: Exhaust camshaft
K: Intake camshaft
011R100011
6. Use J–42609 for installation camshaft oil seal.
014RW075
014RW071
6A–38
ENGINE MECHANICAL (Y22SE 2.2L)
7. Install the camshaft drive pulley. Align the timing mark
between notch on the camshaft drive pulley(1) and
lug on the camshaft bracket(2).
014RW076
Also align a guide hole on the camshaft drive pulley
marked “IN” for intake and “EX” for exhaust to guide
pin on the camshaft when instaling the camshaft drive
pulley.
014RW072
Optional pulley: Must be used on intake camshaft
only.
014R100013
8. Tighten camshaft drive pulley fixing bolt to the
specified torque.
New bolts must be used.
Torque: 50 N·m (37 lb ft) + 60
°
014RW036
9. Install timing belt.
Refer to installation procedure for Timing Belt in this
manual.
10. Install cylinder head cover.
Refer to installation procedure for Cylinder Head
Cover in this manual.
11. Connect battery ground cable.
6A–39
ENGINE MECHANICAL (Y22SE 2.2L)
Engine Assembly
515RX002
Removal
1. Disconnect battery ground and positive cable.
2. Remove battery.
3. Make alignment mark on the engine hood and hinges
before removal in order to return the hood to original
position exactly.
4. Remove engine hood.
5. Drain engine coolant from radiator.
6. Disconnect throttle valve control cable from throttle
valve on intake manifold.
7. Remove air duct with air cleaner cover.
8. Remove air cleaner assembly.
9. Disconnect three engine harness connectors from
chassis harness of left rear side engine compartment.
10. Disconnect vacuum hose on the brake booster.
11. Disconnect cooling fan harness connector on the left
of fan shroud.
12. Disconnect ground cable connector from left and right
of front wheel arch upper side.
13. Remove clutch piping bracket from right side of clutch
housing.
14. Remove fuel piping bracket from transmission.
15. Remove four nuts from exhaust front pipe exhaust
manifold side and remove two bolts from rear side of
exhaust front pipe. Remove exhaust front pipe.
150R100004
6A–40
ENGINE MECHANICAL (Y22SE 2.2L)
16. Remove transmission mounting fixing bolts and nut
from cross member.
022R100006
17. Remove transmission front under cover from front
portion of clutch housing.
18. Disconnect two fuel pipes at right side of transmission
by quick type fuel hose connector.
CAUTION: Plug fuel pipe on engine side and fuel
hose from fuel tank.
19. Disconnect canister hose next to fuel piping
connector.
20. Remove propeller shaft fixing bolt from rear side
transmission.
21. Remove fixing bolts between clutch housing and
transmission, then move transmission.
22. Remove power steering pump assembly then place
the power steering pump along with piping.
23. Disconnect two chassis harness connectors from
right rear side engine compartment (under fuse box)
and remove two harness clips.
24. Remove engine ground cable from chassis frame.
25. Remove radiator lower hose from engine side.
26. Remove two heater hoses from right side panel.
27. Remove radiator grille.
28. Remove harness clip from behind right horn.
29. Remove engine mounting bolt from chassis frame
side.
022RW005
022RW006
30. Lift up the engine assembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст