Isuzu Trooper (1998-2002 year). Manual — part 579
6C – 12 ENGINE FUEL
5. Select “Programming Trim Date” from
Programming menu.
6. Select the injector change from Programming Trim
Date menu.
7. Select the cylinder number which changed injector.
8. Appoint and select the grade code (Category
number) of injector.
9. Confirm the completion of injector programming.
Note; The injector grade code (category number) is
indicated on the new (service part) injector.
Injector
ー
1
Injector
ー
4
Injector
ー
3
Injector
ー
1
Programming Trim Data
Select cylinder
Injector
ー
2
(W) 1998 (UE) Rodeo/Amigo,Wizard
Electronic System
3.0L L4 4JX1
035RW00003
Injector
ー
1
Programming Trim Data
Do you program trim data in
this cylinder
?
(W) 1998 (UE) Rodeo/Amigo,Wizard
Electronic System
3.0L L4 4JX1
Yes
No
035RW00004
Injectorー
1
Programming Trim Data
Programming was succeded
Category A1
(W) 1998 (UE) Rodeo/Amigo,Wizard
Electronic System
3.0L L4 4JX1
Confirmed
035RW00005
ENGINE FUEL 6C – 13
FUEL PUMP PIPE
6
2
3
10
9
8
5
4
7
1
Legend
(1)
Cap Nut
(2)
Gasket
(3)
Gasket
(4)
Pipe Nut
(5)
Adapter
(6)
Gasket
(7)
Fuel Pump Pipe
(8)
Eye Bolt
(9)
Gasket
(10)
Gasket
040R200002
REMOVAL
1. Remove eye bolt.
2. Remove cap nut.
NOTE: The eye bolt and cap nut should be
disconnected with cloth tied around them to prevent
flowing out of fuel.
3. Remove fuel pump pipe.
4. Remove pipe nut.
5. Remove adapter.
INSTALLATION
1. Apply engine oil to the thread, then install adapter
with new gasket.
Torque : 13 N·m (1.3 kg·m/113 lb in)
NOTE: Be careful not to enter the foreign material.
2. Apply engine oil to the thread, then install pipe nut.
Torque : 14 N·m (1.4 kg·m/122 lb in)
NOTE: Do not apply oil to cap nut side.
3. Install fuel pump pipe, new gaskets and cap nut to
adapter temporarily. Do not tighten the cap nut.
4. Install eye bolt with new gasket then tighten to
specified torque.
Torque : 30 N·m (3.1 kg·m/22 lb ft)
6C – 14 ENGINE FUEL
NOTE:
1) Do not apply oil to the eye bolt.
2) Do not bend the fuel pump pipe.
5. Tifhten cap nut to specified torque.
Torque : 13 N·m (1.3 kg·m/113 lb in)
NOTE: Do not apply oil to the cap nut.
6. Start the engine, check that the fuel leakage is not
found.
ENGINE FUEL 6C – 15
HIGH PRESSURE OIL PUMP
REMOVAL
1. Disconnect battery ground cable.
2. Remove air cleaner cover and air duct
3. Intercooler assembly
Refer to “Intercooler” in this manual.
4. Remove high pressure oil pipe
5. Timing belt cover
Disconnect CMP sensor cable.
Remove CMP sensor bracket.
6. Tensioner
7. Timing Belt
8. Remove high pressure oil pump timing pulley
9. Remove crankshaft damper pulley
10. Remove timing gear case cover
11. Remove idle gear A
Before removing idle gear A, set two bolts to the
sub gear of idle gear A and turn it to align the teeth
of idle gear A main gear.
Then lock them by bolts as shown in the illustration.
Legend
(1) Idle gear A sub gear
(2) Idle gear A main gear
(3) Bar
(4) Lock bolt
1
2
4
3
Legend
(1)
O-Ring
(2)
High Pressure Oil Pump Assembly
(3)
Nut
(4)
O-Ring
040RW007
4
1
2
3
014RW177
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст