Isuzu Trooper (1998-2002 year). Manual — part 362
6F–7
ENGINE EXHAUST
Rear Exhaust pipe
Rear Exhaust pipe and Associated Parts
E06RW033
Legend
(1) Mounting Rubber
(2) Rear Exhaust Pipe
(3) Rear Exhaust Pipe Fixing Nuts
Removal
1. Disconnect battery ground cable.
2. Raise the vehicle and support with suitable safety
stands.
3. Remove rear exhaust pipe fixing nuts (3), then
disconnect rear exhaust pipe from exhaust silencer.
4. Remove mounting rubber (1).
5. Remove rear exhaust pipe (2).
Installation
1. Install the mounting rubber (1).
2. Install the exhaust pipe (2) and tighten two nuts (3) on
exhaust silencer to specified torque.
Nuts: 43 N·m (4.4 Kg·m/32 lb ft)
6F–8
ENGINE EXHAUST
Main Data and Specifications
Torque Specifications
N·m (Kg·m/lb ft)
E06RW047
6G–1
ENGINE LUBRICATION
ENGINE
ENGINE LUBRICATION
CONTENTS
Service Precaution
6G–1
. . . . . . . . . . . . . . . . . . . . . .
General Description
6G–2
. . . . . . . . . . . . . . . . . . . . .
Oil Pump
6G–3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pump and Associated Parts
6G–3
. . . . . . . . . .
Oil Pump and Associated Parts
6G–3
. . . . . . . . . .
Inspection and Repair
6G–4
. . . . . . . . . . . . . . . . . .
Reassembly
6G–5
. . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pan and Crankcase
6G–7
. . . . . . . . . . . . . . . . . .
Removal
6G–7
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation
6G–7
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pump
6G–10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal
6G–10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation
6G–10
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pump Oil Seal
6G–12
. . . . . . . . . . . . . . . . . . . . . . .
Removal
6G–12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation
6G–12
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Filter
6G–13
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal
6G–13
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation
6G–13
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Data and Specification
6G–14
. . . . . . . . . . . . . .
Special Tool
6G–15
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Precaution
WARNING: IF SO EQUIPPED WITH A
SUPPLEMENTAL RESTRAINT SYSTEM (SRS),
REFER TO THE SRS COMPONENT AND WIRING
LOCATION VIEW IN ORDER TO DETERMINE
WHETHER YOU ARE PERFORMING SERVICE ON OR
NEAR THE SRS COMPONENTS OR THE SRS
WIRING. WHEN YOU ARE PERFORMING SERVICE
ON OR NEAR THE SRS COMPONENTS OR THE SRS
WIRING, REFER TO THE SRS SERVICE
INFORMATION. FAILURE TO FOLLOW WARNINGS
COULD RESULT IN POSSIBLE AIR BAG
DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener. When
you install fasteners, use the correct tightening
sequence and specifications. Following these
instructions can help you avoid damage to parts and
systems.
6G–2
ENGINE LUBRICATION
General Description
C06RW002
Legend
(1) Oil Strainer
(2) Oil Pump
(3) Relief Valve
(4) Oil Pressure Switch
(5) Oil Filter
(6) Safety Valve
(7) Oil Pressure Unit
(8) Oil Gallery
(9) Crankshaft Bearing
(10) Crankshaft
(11) Connecting Rod Bearing
(12) Connecting Rod
(13) Piston
(14) Oil Gallery; Cylinder Head
(15) Camshaft
(16) Camshaft Journal
(17) Front Journal; Camshaft Drive Gear
(18) Rear Journal; Camshaft Drive Gear
(19) Oil Pan
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст