Isuzu Trooper (1998-2002 year). Manual — part 567
6A – 76 ENGINE MECHANICAL
7) Apply plastigage to the crankshaft journal unit as
shown in the illustration.
8) Install the main bearing caps. Apply engine oil to
the bolt threads and the seats. Tighten the bolts
to the specified torque.
Torque: 167 N·m (17 kg·m/123 lb ft)
NOTE: Do not allow the crankshaft to rotate.
9) Remove the main bearing caps.
10) Measure the plastigage width and determine the
oil clearance. If the oil clearance exceeds the
specified limit, replace the main bearings as a
set and/or replace the crankshaft.
11) Clean the plastigage from the bearings and the
crankshaft.
Remove the crankshaft and the bearings.
Standard: 0.031 – 0.063 mm (0.0012 – 0.0025 in)
Limit: 0.11 mm (0.0043 in)
3. Run-out
1) Carefully set the crankshaft on the V-blocks.
Slowly rotate the crankshaft and measure the
runout. If the crankshaft runout exceeds the
specified limit, the crankshaft must be replaced.
Standard: 0.05 mm (0.0020 in) or less
Limit: 0.08 mm (0.0031 in)
Measure the diameter and the uneven wear of
main journal and crank pin.
If the crankshaft wear exceeds the specified
limit, crankshaft must be replaced.
Main journal diameter
Standard: 69.917 – 69.932 mm (2.7526 – 2.7532 in)
Limit: 69.91 mm (2.7524 in)
Crank pin diameter
Standard: 52.915 – 52.930 mm (2.0833 – 2.0839 in)
Limit: 52.90 mm (2.0827 in)
Uneven wear limit
Standard: 0.05 mm (0.0020 in) or less
Limit: 0.08 mm (0.0031 in)
014RW055
014RW077
012RW068
ENGINE MECHANICAL 6A – 77
Crankshaft inspection
Inspect the surface of the crankshaft journals and crank
pins for excessive wear and damage.
Inspect the oil seal fitting surfaces for excessive wear
and damage.
Inspect the oil ports for obstructions.
Crankshaft tufftriding inspection
1. Use an organic cleaner to thoroughly clean the
crankshaft. There must be no traces of on the
surfaces to be inspected.
2. Prepare a 5 – 10% solution of ammonium cupric
chloride (dissolved in distilled water).
3. Use a syringe to apply the solution to the surface to
be inspected.
Hold the surface to be inspected perfectly
horizontal to prevent the solution from running.
NOTE: Do not allow the solution to come in contact with
the oil ports and their surrounding area (Approximately
10 mm).
Judgment
1. Wait for thirty or forty seconds.
If there is no discoloration after thirty or forty
seconds, the crankshaft is usable.
If discoloration appears (the surface being tested
will become the color of copper), the crankshaft
must be replaced.
2. Steam clean the crankshaft surface immediately
after completing the test.
NOTE: The ammonium cupric chloride solution is highly
corrosive. Because of this, it is imperative that the
surfaces being tested be cleaned immediately after
completing the test.
CRANKSHAFT BEARING SECTION
When installing new crankshaft bearings, refer to the
selection table below.
Select and install the new crankshaft bearings, paying
close attention to the cylinder body journal hole
diameter grade mark and the crankshaft journal
diameter grade mark.
NOTE: Although all upper journal bearings (cylinder
body side) have oil grooves and holes, all lower
bearings (bearing cap side) have no groove and hole.
Play close attention to the distinction during the
installation procedure.
012RW045
The portion to be tested
must be held horizontally
so as not to let the test
solution flow.
The sliding surface
of the pin
or journal.
Test liquid should
not be applied to
the area around the
oil port.
Approximately
10mm
F06MV020
012RW038
6A – 78 ENGINE MECHANICAL
Crankshaft Bearing Bore Grade Mark Position
Crankshaft bearing bore grade marks
1
or
2
are
stamped on the rear right hand side of the cylinder
body.
Example:
No. 1 Bearing No. 2 Bearing No. 3 Bearing No. 4 Bearing No. 5 Bearing
Housing
Housing
Housing
Housing
Housing
Legend
(1) No. 1 Main bearing bore grade
(2) No. 2 Main bearing bore grade
(3) No. 3 Main bearing bore grade
(4) No. 4 Main bearing bore grade
(5) No. 5 Main bearing bore grade
Crankshaft Journal Grade Mark Position
The crankshaft journal grade marks (1 or –) are
stamped on each crankshaft journal wave.
The crankshaft journal and bearing clearance must be
the same for each position after installation of the
crankshaft and the crankshaft bearings.
Legend
(1) Crankshaft journal outside diameter grade
1
2
1
1
2
1
1
1
1
2
2
2
3
4
5
1
2
3
4
5
012RW114
1
015RW078
012RW069
ENGINE MECHANICAL 6A – 79
Main Bearing
Crankshaft
Bore Diameter mm(in)
Main Journal Diameter mm(in)
Crankshaft
Oil Clearance
Grade
Inside Diameter
Grade
Outside Diameter
Bearing
mm(in)
1 or -
69.927 – 69.932
4
0.045 – 0.061
(2.7530 – 2.7532)
(0.0018 – 0.0024)
1
73.992 – 74.000
2 or - -
69.922 – 69.927
4
0.050 – 0.066
(2.9131 – 2.9134)
(2.7528 – 2.7530)
(0.0020 – 0.0026)
3 or - - -
69.917 – 69.922
5
0.052 – 0.068
(2.7526 – 2.7528)
(0.0020 – 0.0027)
1 or -
69.927 – 69.932
2
0.042 – 0.059
(2.7530 – 2.7532)
(0.0017 – 0.0023)
2
73.983 – 73.992
2 or - -
69.922 – 69.927
3
0.044 – 0.061
(2.9127 – 2.9131)
(2.7528 – 2.7530)
(0.0017 – 0.0024)
3 or - - -
69.917 – 69.922
4
0.046 – 0.063
(2.7526 – 2.7528)
(0.0018 – 0.0025)
1 or -
69.927 – 69.932
1
0.037 – 0.053
(2.7530 – 2.7532)
(0.0015 – 0.0021)
3
73.975 – 73.983
2 or - -
69.922 – 69.927
2
0.039 – 0.055
(2.9124 – 2.9127)
(2.7528 – 2.7530)
(0.0015 – 0.0022)
3 or - - -
69.917 – 69.922
2
0.044 – 0.060
(2.7526 – 2.7528)
(0.0017 – 0.0024)
REASSEMBLY
1. Crankshaft
1) Install the main bearings to the cylinder body
and the main bearing caps.
2) Be sure that they are positioned correctly.
3) Apply new engine oil to the upper and lower
main bearing faces.
4) Carefully mount the crankshaft.
5) Apply engine oil to the thrust washer.
6) Assemble the thrust washer to the No. 3 bearing
journal. The oil grooves must face the
crankshaft.
7) Install the bearing caps with the bearing cap
head arrow mark facing the front of the engine.
8) Apply engine oil to the main bearing cap bolts.
9) Tighten the main bearing cap bolts to the
specified torque a little at a time in the sequence
shown in the illustration.
Torque: 167 N·m (17.0 kg·m/123 lb ft)
NOTE: Check to see that the crankshaft turns smoothly
by rotating it manually.
012RW047
8
4
1
5
9
6
10
2
3
7
012RW027
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст