Nissan Almera Tino V10. Manual — part 648
EC-1418
[YD (WITHOUT EURO-OBD)]
DTC P0341 CMP SENSOR
Component Inspection
EBS014XE
CAMSHAFT POSITION SENSOR
1.
Loosen the fixing bolt of the sensor.
2.
Disconnect camshaft position sensor harness connector.
3.
Remove the sensor.
4.
Visually check the sensor for chipping.
5.
Check resistance as shown in the figure.
6.
If NG, replace camshaft position sensor.
Removal and Installation
EBS014XF
CAMSHAFT POSITION SENSOR
Refer to
.
MBIB0647E
Terminal No. (Polarity)
Resistance
Ω
[at 25
°
C (77
°
F)]
3 (+) - 1 (-)
Except 0
3 (+) - 2 (-)
2 (+) - 1 (-)
Except 0 or
∞
MBIB0616E
DTC P0563 BATTERY VOLTAGE
EC-1419
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0563 BATTERY VOLTAGE
PFP:24410
On Board Diagnosis Logic
EBS014XG
The MI will not light up for this self-diagnosis.
DTC Confirmation Procedure
EBS014XH
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and let it idle for at least 35 seconds.
4.
If DTC is detected, go to
EC-1419, "Diagnostic Procedure"
.
Diagnostic Procedure
EBS014XI
1.
INSPECTION START
Are jumper cables connected for the jump starting?
Yes or No
Yes
>> GO TO 3.
No
>> GO TO 2.
2.
CHECK BATTERY AND ALTERNATOR
Check that the proper type of battery and alternator is installed.
Refer to SC-3, “BATTERY”, and SC-24, “CHARGING SYSTEM”.
OK or NG
OK
>> GO TO 5.
NG
>> Replace with a proper one.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0563
Battery voltage high
An excessively high voltage from the battery is
sent to ECM.
●
Battery
●
Battery terminal
●
Alternator
SEF817Y
EC-1420
[YD (WITHOUT EURO-OBD)]
DTC P0563 BATTERY VOLTAGE
3.
CHECK JUMPER CABLES INSTALLATION
Check that the jumper cables are connected in the correct sequence.
OK or NG
OK
>> GO TO 4.
NG
>> Reconnect jumper cables properly.
4.
CHECK BATTERY FOR BOOSTER
Check that the battery for the booster is a 12V battery.
OK or NG
OK
>> GO TO 5.
NG
>> Change the vehicle for booster.
5.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
Perform
EC-1419, "DTC Confirmation Procedure"
, again.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
6.
REPLACE ECM
1.
Replace ECM.
2.
Perform initialization of NATS system and registration of all NATS ignition key IDs. Refer to
"NATS (Nissan Anti-theft System)"
.
3.
Perform Fuel Pump Learning Value Clearing. Refer to
EC-1270, "Fuel Pump Learning Value Clearing"
.
>> INSPECTION END
7.
CHECK ELECTRICAL PARTS DAMAGE
Check the following for damage.
●
Wiring harness and harness connectors for burn
●
Fuses for short
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace malfunctioning part.
SEF439Z
DTC P0605 ECM
EC-1421
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0605 ECM
PFP:23710
Description
EBS014XJ
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM controls the engine.
On Board Diagnosis Logic
EBS014XK
DTC Confirmation Procedure
EBS014XL
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Wait at least 5 seconds.
4.
If DTC is detected, go to
EC-1421, "Diagnostic Procedure"
.
Diagnostic Procedure
EBS014XM
1.
INSPECTION START
With CONSULT-II
1.
Turn ignition switch ON.
2.
Select “SELF DIAG RESULTS” mode with CONSULT-II.
3.
Touch “ERASE”.
4.
Perform
EC-1421, "DTC Confirmation Procedure"
, again.
5.
Is DTC P0605 displayed again?
Yes or No
Yes
>> GO TO 2.
No
>> INSPECTION END
MBIB0625E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0605
Engine control module
(ROM)
ECM ROM is malfunctioning.
●
ECM
SEF817Y
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст