Nissan Almera Tino V10. Manual — part 902
Oil Cooler
NLLC0077
YLC050
REMOVAL AND INSTALLATION
NLLC0077S01
1.
Draining the coolant
Refer to LC-40, “Changing Engine Coolant”.
2.
Remove the exhaust front tube.
SLC359B
3.
Reinstall all removed parts in the reverse order of removal.
I
Confirm that no foreign objects are adhering to the installation
planes of the oil cooler or block.
I
Tighten the connecting bolt after aligning the stopper on the
cylinder block side with protrusion of the oil cooler.
ENGINE LUBRICATION SYSTEM
YD
Oil Cooler
LC-30
Service Data and Specifications (SDS)
OIL PRESSURE CHECK
=NLLC0048
Engine speed
rpm
Approximate discharge pressure
kPa (bar, kg/cm
2
, psi)
Idle speed
More than 140 (1.40, 1.43, 20.3)
2,000
More than 270 (2.69, 2.75, 39.1)
4,000
More than 430 (4.29, 4.38, 62.3)
REGULATOR VALVE INSPECTION
NLLC0049
Unit: mm (in)
Regulator valve to oil pump cover clearance
0.040 - 0.097 (0.0016 - 0.0038)
OIL PUMP INSPECTION
NLLC0050
Unit: mm (in)
Body to outer rotor radial clearance
0.114 - 0.260 (0.0045 - 0.0102)
Inner rotor to outer rotor tip clearance
Below 0.18 (0.0071)
Body to inner rotor axial clearance
0.050 - 0.090 (0.0020 - 0.0035)
Body to outer rotor axial clearance
0.030 - 0.190 (0.0012 - 0.0075)
Inner rotor to brazed portion of housing clearance
0.045 - 0.091 (0.0018 - 0.0036)
ENGINE OIL CAPACITY
NLLC0078
Unit:
(Imp qt)
Drain and refill (Approximately)
Without oil filter chang
e 4.9 (4-3/8
)
With oil filter chang
e 5.2 (4-5
/8)
Dry engine (engine overhaul
) 6.3 (5-1/2
)
GI
MA
EM
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ENGINE LUBRICATION SYSTEM
YD
Service Data and Specifications (SDS)
LC-31
SEM164F
AEM080
Precautions
LIQUID GASKET APPLICATION PROCEDURE
NLLC0051
1.
Use a scraper to remove all traces of old liquid gasket from
mating surfaces and grooves. Also, completely clean any oil
from these areas.
2.
Apply a continuous bead of liquid gasket to mating surfaces.
(Use Genuine Liquid Gasket.)
I
For oil pan, be sure liquid gasket diameter is 4.0 to 5.0 mm
(0.157 to 0.197 in).
I
For areas except oil pan, be sure liquid gasket diameter is 2.0
to 3.0 mm (0.079 to 0.118 in).
3.
Apply liquid gasket around the inner side of bolt holes (unless
otherwise specified).
4.
Assembly should be done within 5 minutes after coating.
5.
Wait at least 30 minutes before refilling engine oil and engine
coolant.
Preparation
SPECIAL SERVICE TOOLS
NLLC0052
Tool number
Tool name
Description
EG17650301
Radiator cap tester
adapter
NT564
Adapting radiator cap tester to radiator filler neck
a: 28 (1.10) dia.
b: 31.4 (1.236) dia.
c: 41.3 (1.626) dia.
Unit: mm (in)
ENGINE COOLING SYSTEM
YD
Precautions
LC-32
Cooling Circuit
NLLC0053
YLC046
GI
MA
EM
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ENGINE COOLING SYSTEM
YD
Cooling Circuit
LC-33
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст