Nissan Almera Tino V10. Manual — part 815
9
CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between ABS actuator and electric unit (control unit) harness connector E142 terminals 26 (L) , 15 (R)
and ground.
YEL456E
OK or NG
OK
GO TO 10.
NG
‰
Repair harness between ABS actuator and electric unit (control unit) and harness con-
nector E125. (LHD models)
‰
Repair harness between ABS actuator and electric unit (control unit) and harness con-
nector E106. (LHD models)
‰
Repair harness between ABS actuator and electric unit (control unit) and harness con-
nector E145. (RHD models)
10
ECM/COMBINATION METER INTERNAL CIRCUIT INSPECTION
Check components inspection. Refer to “ECM/COMBINATION METER INTERNAL CIRCUIT INSPECTION” (EL-557).
OK or NG
OK
Reconnect all connectors to perform “SELF-DIAG RESULTS” and “DATA MONITOR” for
“ENGINE”, “A/T”, “ABS” and “SMART ENTRANCE” displayed on CONSULT-II. Refer to
the following.
‰
“DTC U1000, U1001 CAN COMMUNICATION LINE” (WITH EURO-OBD) (EC-145) for
“ENGINE”
‰
“DTC U1000, U1001 CAN COMMUNICATION LINE” (WITHOUT EURO-OBD) (EC-
651) for “ENGINE”
‰
“DTC U1000 CAN COMMUNICATION LINE” (WITH EURO-OBD) (AT-194) for “A/T”
‰
“CAN COMMUNICATION LINE” (All) (AT-399) for “A/T”
‰
“CAN Communication System” (BR-73) for “ABS”
‰
“CAN Communication Line Check” (EL-351) for “SMART ENTRANCE”
NG
Replace ECM and/or combination meter.
CAN SYSTEM (TYPE 4)
Trouble Diagnoses (Cont’d)
EL-556
SEL723Y
Component Inspection
=NLEL0657
ECM/COMBINATION METER INTERNAL CIRCUIT
INSPECTION
NLEL0657S01
I
Remove ECM and combination meter from vehicle.
I
Check resistance between ECM terminals 94 and 86.
I
Check resistance between combination meter terminals 39
and 40.
Unit
Terminal
Resistance value (
Ω
)
ECM
94 - 86
Approx. 108 - 132
Combination meter
39 - 40
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
CAN SYSTEM (TYPE 4)
Component Inspection
EL-557
Component Parts and Harness Connector
Location
NLEL0668
YEL457E
System Description
NLEL0669
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many
electonic control units are equipped onto a vehicle, and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected with
2 communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wir-
ing. Each control unit transmits/receives data but selectively reads required data only.
CAN SYSTEM (TYPE 5)
Component Parts and Harness Connector Location
EL-558
Wiring Diagram — CAN —
NLEL0670
YEL129E
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
CAN SYSTEM (TYPE 5)
Wiring Diagram — CAN —
EL-559
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст