Nissan Almera Tino V10. Manual — part 137
AT-272
[EXC.F/EURO-OBD]
TROUBLE DIAGNOSIS — BASIC INSPECTION
4.
CHECK VEHICLE MOVE
1.
Apply parking brake.
2.
Move selector lever to “N” position.
3.
Turn ignition switch to “START” position and start engine.
4.
Release parking brake.
5.
Does vehicle move forward or backward?
Yes or No
Yes
>>
●
Mark the box on the DIAGNOSTIC WORKSHEET.
●
GO TO
AT-315, "4. In “N” Position, Vehicle Moves"
.
●
Continue ROAD TEST. Refer to
.
No
>> GO TO 5
5.
CHECK SHIFT SHOCK
1.
Apply foot brake.
2.
Move selector lever to “R” position.
3.
Is there large shock when changing from “N” to “R” position?
Yes or No
Yes
>>
●
Mark the box on the DIAGNOSTIC WORKSHEET.
●
GO TO
.
●
Continue ROAD TEST. Refer to
.
No
>> GO TO 6
6.
CHECK VEHICLE MOVE
1.
Release foot brake for several seconds.
2.
Does vehicle creep backward when foot brake is released?
Yes or No
Yes
>> GO TO 7
No
>>
●
Mark the box on the DIAGNOSTIC WORKSHEET.
●
GO TO
AT-317, "6. Vehicle Does Not Creep Back-
.
●
Continue ROAD TEST. Refer to
.
SAT771B
SAT797A
SAT772B
SAT799A
TROUBLE DIAGNOSIS — BASIC INSPECTION
AT-273
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
7.
CHECK VEHICLE MOVE
1.
Move selector lever to “D”, “2” and “1” positions and check if
vehicle creeps forward.
2.
Does vehicle creep forward in all three positions?
Yes or No
Yes
>> GO TO
.
No
>>
●
Mark the box on the DIAGNOSTIC WORKSHEET.
●
GO TO
AT-320, "7. Vehicle Does Not Creep Forward
.
●
Continue ROAD TEST. Refer to
.
3. CRUISE TEST
●
Check all items listed in Parts 1 through 3.
With CONSULT-II
●
Using CONSULT-II, conduct a cruise test and record the result.
●
Print the result and ensure that shifts and lock-ups take place as per Shift Schedule.
CONSULT-II Setting Procedure
1.
Turn ignition switch “OFF”.
2.
Connect CONSULT-II to data link connector, which is located in
left side lower dash panel.
3.
Turn ignition switch “ON”.
4.
Touch “START (NISSAN BASED VHCL)”.
SAT773B
SAT601J
PAIA0070E
MBIB0233E
AT-274
[EXC.F/EURO-OBD]
TROUBLE DIAGNOSIS — BASIC INSPECTION
5.
Touch “A/T”.
6.
Touch “DATA MONITOR”.
7.
Touch “MAIN SIGNALS” or “TCM INPUT SIGNALS”.
8.
Select “Numerical Display”, “Barchart Display” or “Line Graph
Display”.
9.
Touch “SETTING” to recording condition (“AUTO TRIG” or
“MANU TRIG”) and touch “BACK”.
10. Touch “Start”.
SAT014K
SAT971J
SAT175K
SAT973J
TROUBLE DIAGNOSIS — BASIC INSPECTION
AT-275
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
11. When performing cruise test, touch “RECORD”.
12. After finishing cruise test part 1, touch “STOP”.
13. Touch “STORE” and touch “BACK”.
SAT134K
SAT135K
SAT987J
SAT974J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст