Nissan Almera Tino V10. Manual — part 686
CEL501
Replacement
For removal and installation of spiral cable, refer to RS-24
“Installation — Air Bag Module and Spiral Cable”.
I
Each switch can be replaced without removing combination
switch base.
CEL406
I
To remove combination switch base, remove base attaching
screw.
SEL151V
I
Before installing the steering wheel, align the steering wheel
guide pins with the screws which secure the combination
switch as shown in the left figure.
COMBINATION SWITCH
Replacement
EL-40
Check
NLEL0350
YEL090E
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
STEERING SWITCH
Check
EL-41
Wiring Diagram — H/LAMP —
NLEL0420
YEL926D
HEADLAMP
Wiring Diagram — H/LAMP —
EL-42
Trouble Diagnoses
NLEL0202
Symptom
Possible cause
Repair order
Neither headlamp operates.
1. Lighting switch
1. Check lighting switch.
LH headlamp (low and high beam)
does not operate, but RH head-
lamp (low and high beam) does
operate.
1. 15A fuse
2. Headlamp LH ground circuit
3. Lighting switch
1. Check 15A fuse. Verify battery positive voltage is
present at lighting switch terminal 8.
2. Check headlamp LH ground circuit.
3. Check lighting switch.
RH headlamp (low and high beam)
does not operate, but LH headlamp
(low and high beam) does operate.
1. 15A fuse
2. Headlamp RH ground circuit
3. Lighting switch
1. Check 15A fuse. Verify battery positive voltage is
present at lighting switch terminal 5.
2. Check headlamp RH ground circuit.
3. Check lighting switch.
LH high beam does not operate,
but LH low beam does operate.
1. Bulb
2. Open in LH high beam circuit
3. Lighting switch
1. Check bulb.
2. Check the harness between lighting switch and LH
high beam for an open circuit.
3. Check lighting switch.
LH low beam does not operate, but
LH high beam does operate.
1. Bulb
2. Open in LH low beam circuit
3. Lighting switch
1. Check bulb.
2. Check the harness between lighting switch and LH
low beam for an open circuit.
3. Check lighting switch.
RH high beam does not operate,
but RH low beam does operate.
1. Bulb
2. Open in RH high beam circuit
3. Lighting switch
1. Check bulb.
2. Check the harness between lighting switch and RH
high beam for an open circuit.
3. Check lighting switch.
RH low beam does not operate, but
RH high beam does operate.
1. Bulb
2. Open in RH low beam circuit
3. Lighting switch
1. Check bulb.
2. Check the harness between lighting switch and RH
low beam for an open circuit.
3. Check lighting switch.
High beam indicator does not work. 1. Bulb
2. Ground circuit
3. Open in high beam circuit
1. Check bulb in combination meter.
2. Check harness between high beam indicator and
ground.
3. Check the harness between lighting switch and
combination meter for an open circuit.
NEL713
Bulb Replacement
NLEL0015
The headlamp is a semi-sealed beam type which uses a replace-
able halogen bulb. The bulb can be replaced from the engine com-
partment side without removing the headlamp body.
I
Grasp only the plastic base when handling the bulb. Never
touch the glass envelope.
1.
Disconnect the battery cable.
2.
Pull off the rubber cap.
3.
Disconnect the harness connector from the back side of the
bulb.
4.
Remove the bulb retaining ring.
5.
Remove the headlamp bulb carefully. Do not shake or rotate
the bulb when removing it.
6.
Install in the reverse order of removal.
CAUTION:
Do not leave headlamp reflector without bulb for a long period
of time. Dust, moisture, smoke, etc. entering headlamp body
may affect the performance of the headlamp. Remove head-
lamp bulb from the headlamp reflector just before a replace-
ment bulb is installed.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
HEADLAMP
Trouble Diagnoses
EL-43
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст