Nissan Almera Tino V10. Manual — part 98
AT-116
[EURO-OBD]
DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH
Diagnostic Procedure
ECS0097D
1.
INSPECTION START
Do you have CONSULT-II?
Yes or No
Yes
>> GO TO 2
No
>> GO TO 3
2.
CHECK PNP SWITCH CIRCUIT (WITH CONSULT-II)
With CONSULT-II
1.
Turn ignition switch to “ON” position.
(Do not start engine.)
2.
Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for
“A/T” with CONSULT-II.
3.
Read out “P/N”, “R”, “D”, “2” and “1” position switches moving
selector lever to each position.
Check the signal of the selector lever position is indicated prop-
erly.
OK or NG
OK
>> GO TO 4
NG
>> Check the following items:
●
PNP switch
Refer to
AT-118, "Component Inspection"
.
●
Harness for short or open between ignition switch and
PNP switch (Main harness)
●
Harness for short or open between PNP switch and
TCM (Main harness)
●
Ignition switch and fuse
Refer to EL-11, “Power Supply Routing”.
●
Diode (P, N positions)
SAT014K
SAT701J
DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH
AT-117
[EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
3.
CHECK PNP SWITCH CIRCUIT (WITHOUT CONSULT-II)
Without CONSULT-II
1.
Turn ignition switch to “ON” position.
(Do not start engine.)
2.
Check voltage between TCM terminals 26, 27, 34, 35, 36 and ground while moving selector lever through
each position.
OK or NG
OK
>> GO TO 4
NG
>> Check the following items:
●
PNP switch
Refer to
AT-118, "Component Inspection"
.
●
Harness for short or open between ignition switch and PNP switch (Main harness)
●
Harness for short or open between PNP switch and TCM (Main harness)
●
Ignition switch and fuse
Refer to EL-11, “Power Supply Routing”.
●
Diode (P, N positions)
Voltage:
B: Battery voltage
0: 0V
MTBL0136
SCIA0753E
AT-118
[EURO-OBD]
DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH
4.
CHECK DTC
Perform
AT-113, "DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION PROCEDURE"
.
OK or NG
OK
>> INSPECTION END
NG
>> 1. Perform TCM input/output signal inspection.
2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
Component Inspection
ECS0097E
PARK/NEUTRAL POSITION (PNP) SWITCH
1.
Check continuity between terminals 1 and 3 and between termi-
nals 2 and 4, 5, 6, 7, 8, 9 while moving manual shaft through
each position.
2.
If NG, check again with control cable disconnected from manual
shaft of A/T assembly. Refer to step 1.
3.
If OK on step 2, adjust control cable. Refer to
.
4.
If NG on step 2, remove PNP switch from A/T and check conti-
nuity of PNP switch terminals. Refer to step 1.
5.
If OK on step 4, adjust PNP switch. Refer to
tral Position (PNP) Switch Adjustment"
.
6.
If NG on step 4, replace PNP switch.
Lever position
Terminal No.
P
3 — 7
1 — 2
R
3 — 8
N
3 — 9
1 — 2
D
3 — 6
2
3 — 5
1
3 — 4
MCIA0068E
SAT089JA
DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT
AT-119
[EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT
PFP:31940
Description
ECS0097F
The A/T fluid temperature sensor detects the A/T fluid temperature
and sends a signal to the TCM.
CONSULT-II REFERENCE VALUE IN DATA MONITOR MODE
Remarks: Specification data are reference values.
TCM TERMINALS AND REFERENCE VALUE
Remarks: Specification data are reference values.
ON BOARD DIAGNOSIS LOGIC
DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE” has been previously conducted,
always turn ignition switch “OFF” and wait at least 5 seconds before conducting the next test.
SCIA0735E
SAT021J
Monitor item
Condition
Specification (Approximately)
A/T fluid temperature sensor
Cold [20
°
C (68
°
F)]
↓
Hot [80
°
C (176
°
F)]
1.5V
↓
0.5V
2.5 k
Ω
↓
0.3 k
Ω
Termi-
nal No.
Wire color
Item
Condition
Judgement stan-
dard
(Approx.)
42
B
Sensor ground
—
—
—
47
BR
A/T fluid tempera-
ture sensor
When ATF temperature is 20
°
C
(68
°
F).
1.5V
When ATF temperature is 80
°
C
(176
°
F).
0.5V
Diagnostic trouble code
Malfunction is detected when...
Check items (Possible cause)
: ATF TEMP SEN/CIRC
TCM receives an excessively low or high
voltage from the sensor.
●
Harness or connectors
(The sensor circuit is open or shorted.)
●
A/T fluid temperature sensor
: P0710
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст