Nissan Almera Tino V10. Manual — part 581
EC-1150
[YD (WITH EURO-OBD)]
DTC P0404 EGR VOLUME CONTROL VALVE
Without CONSULT-II
1.
Disconnect EGR volume control valve harness connector.
2.
Check resistance between the following terminals.
●
terminal 2 and terminals 1, 3
●
terminal 5 and terminals 4, 6
If NG, replace EGR volume control valve.
If OK, go to next step.
3.
Remove EGR volume control valve from cylinder head.
4.
Reconnect EGR volume control valve harness connector.
5.
Turn ignition switch ON and OFF.
6.
Check that EGR volume control valve shaft moves smoothly for-
ward and backward according to the ignition switch position.
If NG, replace EGR volume control valve.
NOTE:
When installing the EGR volume control valve, make sure that
the shaft is in the same position before checking.
Removal and Installation
EBS013DY
EGR VOLUME CONTROL VALVE
Refer to
.
Temperature
°
C (
°
F)
Resistance
Ω
20 (68)
13 - 17
MBIB0007E
SEF560W
DTC P0563 BATTERY VOLTAGE
EC-1151
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0563 BATTERY VOLTAGE
PFP:24410
On Board Diagnosis Logic
EBS013DZ
This self-diagnosis has the one trip detection logic.
The MI will not light up for this self-diagnosis.
DTC Confirmation Procedure
EBS013E0
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and let it idle for at least 35 seconds.
4.
If DTC is detected, go to
EC-1151, "Diagnostic Procedure"
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
Diagnostic Procedure
EBS013E1
1.
INSPECTION START
Are jumper cables connected for the jump starting?
Yes or No
Yes
>> GO TO 3.
No
>> GO TO 2.
2.
CHECK BATTERY AND ALTERNATOR
Check that the proper type of battery and alternator is installed.
Refer to SC-3, “BATTERY” and SC-24, “CHARGING SYSTEM”.
OK or NG
OK
>> GO TO 5.
NG
>> Replace with a proper one.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0563
Battery voltage high
An excessively high voltage from the battery is
sent to ECM.
●
Battery
●
Battery terminal
●
Alternator
SEF817Y
EC-1152
[YD (WITH EURO-OBD)]
DTC P0563 BATTERY VOLTAGE
3.
CHECK JUMPER CABLES INSTALLATION
Check that the jumper cables are connected in the correct sequence.
OK or NG
OK
>> GO TO 4.
NG
>> Reconnect jumper cables properly.
4.
CHECK BATTERY FOR BOOSTER
Check that the battery for the booster is a 12V battery.
OK or NG
OK
>> GO TO 5.
NG
>> Change the vehicle for booster.
5.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
Perform
EC-1151, "DTC Confirmation Procedure"
, again.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
6.
REPLACE ECM
1.
Replace ECM.
2.
Perform initialization of NATS system and registration of all NATS ignition key IDs. Refer to
"NATS (Nissan Anti-theft System)"
.
3.
Perform Fuel Pump Learning Value Clearing. Refer to
EC-956, "Fuel Pump Learning Value Clearing"
.
>> INSPECTION END
7.
CHECK ELECTRICAL PARTS DAMAGE
Check the following for damage.
●
Wiring harness and harness connectors for burn
●
Fuses for short
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace malfunctioning part.
SEF439Z
DTC P0605 ECM
EC-1153
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0605 ECM
PFP:23710
Description
EBS013E2
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM controls the engine.
On Board Diagnosis Logic
EBS013E3
DTC Confirmation Procedure
EBS013E4
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Wait at least 5 seconds.
4.
If 1st trip DTC is detected, go to
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
MBIB0625E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0605
Engine control module
(ROM)
ECM ROM is malfunctioning.
●
ECM
SEF817Y
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст