Nissan Almera Tino V10. Manual — part 653
EC-1438
[YD (WITHOUT EURO-OBD)]
DTC P0652, P0653 SENSOR POWER SUPPLY
Diagnostic Procedure
EBS014YF
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten body ground screw. Refer to
.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connection.
2.
CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT
1.
Disconnect accelerator pedal position (APP) sensor harness
connector.
2.
Turn ignition switch ON.
3.
Check voltage between APP sensor terminal 1 and ground with
CONSULT-II or tester.
OK or NG
OK
>> GO TO 3.
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
3.
CHECK APP SENSOR
Refer to
EC-1439, "Component Inspection"
.
OK or NG
OK
>> GO TO 4.
NG
>> Replace accelerator pedal assembly.
4.
CHECK INTERMITTENT INCIDENT
Refer to
EC-1309, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
MBIB0915E
MBIB0904E
Voltage: Approximately 5.3V
PBIB0812E
DTC P0652, P0653 SENSOR POWER SUPPLY
EC-1439
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Component Inspection
EBS014YG
ACCELERATOR PEDAL POSITION SENSOR
1.
Reconnect all harness connectors disconnected.
2.
Turn ignition switch ON.
3.
Check voltage between ECM terminals 83 (APP sensor 1 sig-
nal), 91 (APP sensor 2 signal) and engine body under the fol-
lowing conditions.
4.
If NG, replace accelerator pedal assembly.
Removal and Installation
EBS014YH
ACCELERATOR PEDAL
Refer to FE-16, “ACCELERATOR CONTROL SYSTEM”.
Terminal
Accelerator pedal
Voltage
83
(Accelerator pedal position
sensor 1)
Fully released
0.5 - 1.0V
Fully depressed
4.2 - 5.2V
91
(Accelerator pedal position
sensor 2)
Fully released
0.4 - 0.7V
Fully depressed
2.2 - 2.7V
MBIB0615E
EC-1440
[YD (WITHOUT EURO-OBD)]
DTC P0686 ECM RELAY
DTC P0686 ECM RELAY
PFP:25230
ECM Terminals and Reference valve
EBS014YI
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
On Board Diagnosis Logic
EBS014YJ
The MI will not light up for this self-diagnosis.
DTC Confirmation Procedure
EBS014YK
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON and then turn OFF.
2.
Wait at least 30 seconds.
3.
Turn ignition switch ON.
4.
Select “DATA MONITOR” mode with CONSULT-II.
5.
If DTC is detected, go to
EC-1442, "Diagnostic Procedure"
.
TERMI-
NAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA
(DC Voltage)
105
113
G
G
ECM relay (self-shutoff)
[Ignition switch ON]
[Ignition switch OFF]
●
For a few seconds after turning ignition switch
OFF
Approximately 1.2V
[Ignition switch OFF]
●
More than a few seconds after turning ignition
switch OFF
BATTERY VOLTAGE
(11 - 14V)
107
108
W/R
W/R
Ignition switch
[Ignition switch ON]
BATTERY VOLTAGE
(11 - 14V)
119
120
R
R
Power supply for ECM
[Ignition switch ON]
BATTERY VOLTAGE
(11 - 14V)
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0686
ECM relay circuit
ECM detects ECM relay is stuck closed even if
ignition switch OFF.
●
Harness or connectors
(The ECM relay circuit is shorted.)
●
ECM relay
SEF817Y
DTC P0686 ECM RELAY
EC-1441
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Wiring Diagram
EBS014YL
MBWA0655E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст