Nissan Almera Tino V10. Manual — part 140
AT-284
[EXC.F/EURO-OBD]
TROUBLE DIAGNOSIS — BASIC INSPECTION
6.
CHECK ENGINE BRAKE
Does vehicle decelerate by engine brake?
Yes or No
Yes
>> 1. Stop vehicle.
2. Perform self-diagnosis.
Refer to
AT-252, "SELF-DIAGNOSTIC PROCEDURE
,
No
>>
●
GO TO
AT-337, "20. Vehicle Does Not Decelerate By
.
●
Continue ROAD TEST. Refer to
.
SAT778B
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
AT-285
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
PFP:00000
Symptom Chart
ECS009A2
Numbers are arranged in order of inspection.
Perform inspections starting with number one and work up.
Symptom
Condition
Diagnostic Item
Reference Page
Engine cannot start in “P” and “N”
positions.
AT-313, "2. Engine Cannot Be Started
In “P” and “N” Position"
ON vehicle
1. Ignition switch and starter
EL-11, “Power Supply
Routing”, SC-13, “Start-
ing System”.
2. Control cable adjustment
AT-412, "Control Cable
Adjustment"
3. PNP switch adjustment
AT-412, "Park/Neutral
Position (PNP) Switch
Adjustment"
Engine starts in position other than
“N” and “P” positions.
AT-313, "2. Engine Cannot Be Started
In “P” and “N” Position"
ON vehicle
1. Control cable adjustment
AT-412, "Control Cable
Adjustment"
2. PNP switch adjustment
AT-412, "Park/Neutral
Position (PNP) Switch
Adjustment"
Transaxle noise in “P” and “N” posi-
tions.
ON vehicle
1. Fluid level
2. Line pressure test
3. Throttle position sensor (Accelerator
pedal position (APP) sensor)
AT-356, "ACCELE
RATOR PEDAL POSI-
TION (APP) SENSOR"
4. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTR
AT-347, "VEHICLE
SPEED SENSOR - A/T
(REVOLUTION SEN-
SOR)"
AT-352, "DTC VEHICLE
SPEED SENSOR MTR"
5. Engine speed signal
OFF vehicle
6. Oil pump
7. Torque converter
AT-421, "Locations of
Adjusting Shims, Needle
Bearings, Thrust Washers
and Snap Rings"
Vehicle moves when changing into “P”
position, or parking gear does not dis-
engage when shifted out of “P” posi-
tion.
AT-313, "3. In “P” Position, Vehicle
Moves Forward Or Backward When
Pushed"
ON vehicle
1. Control cable adjustment
AT-412, "Control Cable
Adjustment"
OFF vehicle
2. Parking components
AT-482, "Output Shaft,
Idler Gear, Reduction Pin-
ion Gear and Bearing
Retainer"
Vehicle runs in “N” position.
AT-315, "4. In “N” Position, Vehicle
Moves"
ON vehicle
1. Control cable adjustment
AT-412, "Control Cable
Adjustment"
OFF vehicle
2. Forward clutch
AT-468, "Forward and
Overrun Clutches"
3. Reverse clutch
4. Overrun clutch
AT-286
[EXC.F/EURO-OBD]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Vehicle will not run in “R” position (but
runs in “D”, “2” and “1” positions).
Clutch slips.
Very poor acceleration.
AT-317, "6. Vehicle Does Not Creep
Backward In “R” Position"
ON vehicle
1. Control cable adjustment
AT-412, "Control Cable
Adjustment"
2. Line pressure test
3. Line pressure solenoid valve
AT-392, "LINE PRES-
SURE SOLENOID
VALVE"
4. Control valve assembly
AT-410, "Control Valve
Assembly and Accumula-
tors"
OFF vehicle
5. Reverse clutch
6. High clutch
7. Forward clutch
AT-468, "Forward and
Overrun Clutches"
8. Overrun clutch
AT-468, "Forward and
Overrun Clutches"
9. Low & reverse brake
Vehicle braked when shifting into “R”
position.
ON vehicle
1. Fluid level
2. Control cable adjustment
AT-412, "Control Cable
Adjustment"
3. Line pressure test
4. Line pressure solenoid valve
AT-392, "LINE PRES-
SURE SOLENOID
VALVE"
5. Control valve assembly
AT-410, "Control Valve
Assembly and Accumula-
tors"
OFF vehicle
6. High clutch
7. Brake band
AT-487, "Band Servo Pis-
ton Assembly"
8. Forward clutch
AT-468, "Forward and
Overrun Clutches"
9. Overrun clutch
AT-468, "Forward and
Overrun Clutches"
Symptom
Condition
Diagnostic Item
Reference Page
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
AT-287
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Sharp shock in shifting from “N” to “D”
position.
ON vehicle
1. Engine idling rpm
EC-936, "Idle Speed and
Ignition Timing"
2. Throttle position sensor Accelerator
pedal position (APP) sensor Adjustment
AT-356, "ACCELE
RATOR PEDAL POSI-
TION (APP) SENSOR"
3. Line pressure test
4. A/T fluid temp sen circ and TCM pow
sour
AT-381, "BATT/FLUID
TEMP SEN (A/T FLUID
TEMP SENSOR CIR-
CUIT AND TCM POWER
SOURCE)"
5. Engine speed signal
6. Line pressure solenoid valve
AT-392, "LINE PRES-
SURE SOLENOID
VALVE"
7. Control valve assembly
AT-410, "Control Valve
Assembly and Accumula-
tors"
8. Accumulator N-D
AT-410, "Control Valve
Assembly and Accumula-
tors"
OFF vehicle
9. Forward clutch
AT-468, "Forward and
Overrun Clutches"
Vehicle will not run in “D” and “2” posi-
tions (but runs in “1” and “R” posi-
tions).
ON vehicle
1. Control cable adjustment
AT-412, "Control Cable
Adjustment"
OFF vehicle
2. Low one-way clutch
AT-421, "Locations of
Adjusting Shims, Needle
Bearings, Thrust Washers
and Snap Rings"
Vehicle will not run in “D”, “1”, “2” posi-
tions (but runs in “R” position). Clutch
slips. Very poor acceleration.
AT-320, "7. Vehicle Does Not Creep
Forward In “D”, “2” Or “1” Position"
ON vehicle
1. Fluid level
2. Line pressure test
3. Line pressure solenoid valve
AT-392, "LINE PRES-
SURE SOLENOID
VALVE"
4. Control valve assembly
AT-410, "Control Valve
Assembly and Accumula-
tors"
5. Accumulator N-D
AT-410, "Control Valve
Assembly and Accumula-
tors"
OFF vehicle
6. Reverse clutch
7. High clutch
8. Forward clutch
AT-468, "Forward and
Overrun Clutches"
9. Forward one-way clutch
10. Low one-way clutch
AT-421, "Locations of
Adjusting Shims, Needle
Bearings, Thrust Washers
and Snap Rings"
Symptom
Condition
Diagnostic Item
Reference Page
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст