Nissan Almera Tino V10. Manual — part 62
NOTES
FRONT & REAR SUSPENSION
CONTENTS
FRONT SUSPENSION . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . ..2
. . . . . . . . . . . . . . .2
Preparation . . . . . . . . . . . . . . . . ..2
. . . . . . . . . . 2
. . . . . . . . 2
Noise, Vibration and Harshness (NVH)
Troubleshooting . . . . . . . . . . . . . . ...4
. . . . . . . 4
Components. . . . . . . . . . . . . . . . .5
On-vehicle Service. . . . . . . . . . . . . ...6
. . . . . . . . ...6
. . . . . . . . . . . ...6
. . . . . . . . . . . . . ...8
. . . . . . . . . .8
Coil Spring and Shock Absorber . . . . . . . ...10
. . . . . . . . . . . . . ...10
. . . . . . . ... 11
. . . . . . . . . . . . . . 11
. . . . . . . . . . . . . . ... 11
. . . . . . . . . . . . . . . .12
Stabilizer Bar . . . . . . . . . . . . . . . .12
. . . . . . . ...12
Transverse Link and Lower Ball Joint . . . . . ...13
. . . . . . . ...13
. . . . . . . . . . . . . . ...13
Service Data and Specifications (SDS). . . . . .15
GENERAL SPECIFICATIONS (FRONT)
. . . . . .15
FRONT WHEEL ALIGNMENT (UNLADEN*1)
. . . .15
. . . . . . . . . . . ...15
. . . . . ...16
. . . . . . . . . . . . . 16
. . . . . . . . . . . . ...16
REAR SUSPENSION. . . . . . . . . . . . . .17
Precautions . . . . . . . . . . . . . . . . 17
. . . . . . . . . . . . . ...17
Preparation . . . . . . . . . . . . . . . . 17
. . . . . . . ..17
Noise, Vibration and Harshness (NVH)
Troubleshooting . . . . . . . . . . . . . . .17
Components. . . . . . . . . . . . . . . ...18
On-vehicle Service. . . . . . . . . . . . . .19
. . . . . . . . ...19
. . . . . . . . . .19
Removal and Installation . . . . . . . . . . ...22
. . . . . . . . . . . . . . . ...23
. . . . . . . . . . . . . . 23
Coil Spring and Shock Absorber . . . . . . . ...23
. . . . . . . ...23
. . . . . . . . . . . . . . 24
. . . . . . . . . . . . . . ...24
. . . . . . . . . . . . . . . .24
Torsion Beam, Lateral Link and Control Rod . . . 25
. . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . ...25
. . . . . . . . . . . . . . . .25
Service Data and Specifications (SDS). . . . . .27
. . . . . ...27
REAR WHEEL ALIGNMENT (UNLADEN*)
. . . . .27
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
BR
ST
RS
BT
HA
SC
EL
IDX
SBR686C
Precautions
PRECAUTIONS
NLSU0001
I
When installing rubber parts, final tightening must be car-
ried out under unladen condition* with tires on ground.
Oil will shorten the life of rubber bushes. Be sure to wipe
off any spilled oil.
*: Fuel, radiator coolant and engine oil full. Spare tire, jack,
hand tools and mats in designated positions.
I
After installing removed suspension parts, check wheel
alignment and adjust if necessary.
I
Use flare nut wrench when removing or installing brake
tubes.
I
Always torque brake lines when installing.
I
Lock nuts are unreusable parts; always use new ones.
When replacing, do not wipe the oil off the new lock nut
before tightening.
Preparation
SPECIAL SERVICE TOOLS
NLSU0002
Tool number
Tool name
Description
HT72520000
Ball joint remover
NT146
Removing tie-rod outer end and lower ball joint
COMMERCIAL SERVICE TOOLS
NLSU0003
Tool name
Description
Attachment Wheel align-
ment
NT148
Measure wheel alignment
a: Screw M24 x 1.5 pitch
b: 35 mm (1.38 in) dia.
c: 65 mm (2.56 in) dia.
d: 56 mm (2.20 in)
e: 12 mm (0.47 in)
1 Flare nut crowfoot
2 Torque wrench
NT360
Removing and installing each brake piping
a: 10 mm (0.39 in)
FRONT SUSPENSION
Precautions
SU-2
Tool name
Description
Spring compressor
NT717
Removing and installing coil spring
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
BR
ST
RS
BT
HA
SC
EL
IDX
FRONT SUSPENSION
Preparation (Cont’d)
SU-3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст