Nissan Almera Tino V10. Manual — part 351
EC-230
[QG (WITH EURO-OBD)]
DTC P0134 HO2S1 (M/T MODELS)
DTC P0134 HO2S1 (M/T MODELS)
PFP:22690
Component Description
EBS00QK7
The heated oxygen sensor 1 is placed into the exhaust manifold. It
detects the amount of oxygen in the exhaust gas compared to the
outside air. The heated oxygen sensor 1 has a closed-end tube
made of ceramic zirconia. The zirconia generates voltage from
approximately 1V in richer conditions to 0V in leaner conditions. The
heated oxygen sensor 1 signal is sent to the ECM. The ECM adjusts
the injection pulse duration to achieve the ideal air-fuel ratio. The
ideal air-fuel ratio occurs near the radical change from 1V to 0V.
CONSULT-II Reference Value in Data Monitor Mode
EBS00QK8
Specification data are reference values.
On Board Diagnosis Logic
EBS00QK9
Under the condition in which the heated oxygen sensor 1 signal is
not input, the ECM circuits will read a continuous approximately
0.3V. Therefore, for this diagnosis, the time that output voltage is
within 200 to 400 mV range is monitored, and the diagnosis checks
that this time is not inordinately long.
SEF463R
SEF288D
MONITOR ITEM
CONDITION
SPECIFICATION
HO2S1 (B1)
●
Engine: After warming up
Maintaining engine speed at 2,000
rpm
0 - 0.3V
←→
Approx. 0.6 - 1.0V
HO2S1 MNTR (B1)
LEAN
←→
RICH
Changes more than 5 times dur-
ing 10 seconds.
SEF237U
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0134
0134
Heated oxygen sensor 1
circuit no activity detected
The voltage from the sensor is constantly
approx. 0.3V.
●
Harness or connectors
(The sensor circuit is open or shorted.)
●
Heated oxygen sensor 1
DTC P0134 HO2S1 (M/T MODELS)
EC-231
[QG (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC Confirmation Procedure
EBS00QKA
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously conducted, always turn ignition switch “OFF” and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11V at idle.
WITH CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Select “HO2S1 (B1) P0134” of “HO2S1” in “DTC WORK SUPPORT” mode with CONSULT-II.
3.
Touch “START”.
4.
Let it idle for at least 3 minutes.
NOTE:
Never raise engine speed above 3,600 rpm after this step. If
the engine speed limit is exceeded, return to step 4.
5.
When the following conditions are met, “TESTING” will be dis-
played on the CONSULT-II screen. Maintain the conditions con-
tinuously until “TESTING” changes to “COMPLETED”. (It will
take approximately 10 to 60 seconds.)
If “TESTING” is not displayed after 5 minutes, retry from
step 2.
6.
Make sure that “OK” is displayed after touching “SELF-DIAG
RESULTS”. If “NG” is displayed, refer to
.
Overall Function Check
EBS00QKB
Use this procedure to check the overall function of the heated oxygen sensor 1 circuit. During this check, a
DTC might not be confirmed.
WITH GST
1.
Start engine and warm it up to normal operating temperature.
2.
Set voltmeter probes between ECM terminal 35 (HO2S1 signal) and engine ground.
PBIB0544E
ENG SPEED
1,700 - 4,000 rpm
Vehicle speed
More than 64 km/h (40 MPH)
B/FUEL SCHDL
3.0 - 9.5 msec
Selector lever
Suitable position
PBIB0545E
SEC750C
EC-232
[QG (WITH EURO-OBD)]
DTC P0134 HO2S1 (M/T MODELS)
3.
Check the following with engine speed held at 2,000 rpm con-
stant under no load.
–
The voltage does not remain in the range of 0.2 to 0.4V.
4.
If NG, go to
EC-234, "Diagnostic Procedure"
.
MBIB0018E
DTC P0134 HO2S1 (M/T MODELS)
EC-233
[QG (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Wiring Diagram
EBS00QKC
YEC443A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст