Nissan Almera Tino V10. Manual — part 644
EC-1402
[YD (WITHOUT EURO-OBD)]
DTC P0336 CKP SENSOR
On Board Diagnosis Logic
EBS014WU
DTC Confirmation Procedure
EBS014WV
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and let it idle for at least 5 seconds.
If engine could not start, keep ignition switch at START position
for 5 seconds.
4.
If 1st trip DTC is detected, go to
.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0336
Crankshaft position sensor
circuit range/performance
Crankshaft position sensor signal is not in the
normal pattern when engine is running.
●
Harness or connectors
(The sensor circuit is open or shorted.)
●
Crankshaft position sensor
●
Signal plate
SEF817Y
DTC P0336 CKP SENSOR
EC-1403
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Wiring Diagram
EBS014WW
YEC504A
EC-1404
[YD (WITHOUT EURO-OBD)]
DTC P0336 CKP SENSOR
Diagnostic Procedure
EBS014WX
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten body ground screw. Refer to
.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connection.
2.
CHECK CKP SENSOR POWER SUPPLY CIRCUIT
1.
Disconnect crankshaft position sensor harness connector.
2.
Turn ignition switch ON.
3.
Check voltage between CKP sensor terminal 3 and ground with
CONSULT-II or tester.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 3.
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
3.
CHECK CKP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between ECM terminal 65 and CKP sensor terminal 2.
Refer to Wiring Diagram.
4.
Also check harness for and short to ground and short to power.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
MBIB0915E
MBIB0863E
Voltage: Approximately 5.3V
SEF646P
Continuity should exist.
DTC P0336 CKP SENSOR
EC-1405
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
4.
CHECK CKP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check harness continuity between ECM terminal 46 and CKP sensor terminal 1.
Refer to Wiring Diagram.
2.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK CRANKSHAFT POSITION SENSOR
Refer to
EC-1405, "Component Inspection"
.
OK or NG
OK
>> GO TO 6.
NG
>> Replace crankshaft position sensor.
6.
CHECK GEAR TOOTH
Visually check for chipping signal plate gear tooth.
OK or NG
OK
>> GO TO 7.
NG
>> Replace the signal plate.
7.
CHECK INTERMITTENT INCIDENT
Refer to
EC-1309, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Component Inspection
EBS014WY
CRANKSHAFT POSITION SENSOR
1.
Loosen the fixing bolt of the sensor.
2.
Disconnect crankshaft position sensor harness connector.
3.
Remove the sensor.
4.
Visually check the sensor for chipping.
Continuity should exist.
MBIB0864E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст