Nissan Almera Tino V10. Manual — part 718
Terminals and Reference Value
NLEL0688
TERMINALS
ITEM
CONDITION
Voltage [V]
(+)
(–)
TERMI-
NAL
WIRE
COLOR
Ignition
switch
Operation
2
R
Ground
Image signal
(output
ON
Gear position: “R” position
Approximately 0V
MKIB0189E
3
W
Ground
Camera image
signal (input)
ON
Gear position “R” position
Approximately 0V
MKIB0189E
5
PU
Ground
Camera power
output
ON
Gear position: R-position
Approximately 6.5V
6
P
Ground ACC power
ACC
—
Battery voltage
7
Y
Ground Battery power
OFF
—
Battery voltage
9
B
Ground Shield ground
ON
—
—
10
B
Ground Shield ground
ON
—
—
13
L
Ground
Image synchro-
nous signal (out-
put)
ON
Gear position: R-position
Approximately 5V
MKIB0190E
14
G/W
Ground
Reverse signal
input
ON
Gear position: “R” position
Battery voltage
Gear position: Other position
Approximately 0V
15
PU/W
Ground
Connected recog-
nition signal
ON
—
Approximately 0V
16
B
Ground Ground
ON
—
—
REARVIEW MONITOR
Terminals and Reference Value
EL-168
Trouble Diagnosis
NLEL0541
POWER SUPPLY AND GROUND CIRCUIT CHECK
NLEL0541S02
1
CHECK THE FUSES
I
Check that the fuses for rearview camera control unit are blown.
MTBL1644
OK or NG
OK
©
GO TO 2.
NG
©
If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse.
Refer to EL-12.
2
POWER SUPPLY CIRCUIT CHECK
1. Disconnect camera controller connector.
2. Check voltage rearview camera control unit B64 (LHD models) or B116 (RHD models) terminal 6 (P) and 7(Y), and
ground.
YEL604E
MTBL1645
OK or NG
OK
©
GO TO 3.
NG
©
Check harness for open or short between rearview camera control unit and fuse.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
REARVIEW MONITOR
Trouble Diagnosis
EL-169
3
GROUND CIRCUIT CHECK
Check the following.
I
Continuity between rearview camera control unit harness connector B64 (LHD models) or B116 (RHD models) terminal
16 (B) and ground.
YEL606E
Continuity should exist.
OK or NG
OK
©
INSPECTION END
NG
©
Check ground harness.
REARVIEW MONITOR
Trouble Diagnosis (Cont’d)
EL-170
REARVIEW IS NOT DISPLAYED WITH THE SELECTOR
LEVER IN R-POSITION.
=NLEL0541S03
1
BACKUP LAMP INSPECTION
1. Turn ignition switch ON position.
2. Shift the selector lever to R-position.
Does backup lamp illuminate?
Yes
©
GO TO 2.
No
©
Check backup lamp system.
2
CHECK REVERSE POSITION INPUT SIGNAL I
1. Turn ignition switch OFF.
2. Disconnect rearview camera control unit connector.
3. Turn ignition switch ON.
4. Shift the selector lever to R-position.
5. Check voltage between rearview camera control unit harness connector B64 (LHD models) or B116 (RHD models) ter-
minal 14 (G/W) and ground.
YEL603E
Battery voltage should exist.
OK or NG
OK
©
GO TO 3.
(With navigation system)
OK
©
GO TO 4.
(Without navigation system)
NG
©
Check harness for open or short between rearview camera control unit and backup lamp
switch (M/T models) or park/neutral position switch (A/T models).
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
REARVIEW MONITOR
Trouble Diagnosis (Cont’d)
EL-171
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст